Casals CCH26REAK Instrucciones Originales página 5

diately Product description and Specifications
nt the
Description (Fig. 1,2,3)
oor, if
A Drill chuck (SDS-Plus)
B Chuck sliding ring
C Drilling / Hammer / Hammer Drilling Selector
et, or D Rotation direction switch
E Auxiliary handle
F Depth Gauge
G Cooling vents
ngled H Start-up switch
I Locking Button
J Drill Chuck
h use. K SDS-plus adaptador
e not L Mounting screw
M Button
es or
them Installation
Auxiliary Operation
direct - Operate the appliance only with the auxiliary handle.
- Turn the auxiliary handle in counter clockwise direction for
y of a adjustment (E)
- Set the auxiliary handle on the appliance into the required
ch the position.
- Tighten the auxiliary handle (E) by turning it in clockwise
at the direction.
with a - The depth can be set with the depth stop (F). Thereby
press the button (M) and set de required drilling depth.
orked - Release pressure on the button (M).
ree to
conds Instructions for use
other Before use:
ck the - Make sure that all the product's packaging has been
es and removed.
- Prepare the appliance according to the function you
r dust wish to use:
Fitting the working tools: (Fig. 2)
ur - Unplug the appliance from the mains.
t, - Only use tools with SDS-plus shaft.
- Clean and grease the shaft of the tool.
- Install the drill bit or accessory in the drill chuck. Turn the
drill bit slightly until it can be pushed in all the way and you
rvised can feel it engages into place.
- Ensure that the drill bit is locked.
res.
encing SDS-plus adapter for drilling in wood or metal (Fig. 3)
a. - Unplug the appliance from the mains.
m the - Fit the SDS-plus adapter (K) into the SDS-plus chuck as
described above "fitting the working tools"
- Screw the Drill Chuck (J) on the mounting shaft and
Screw the mounting Screw (L).
- To open the drill's chuck, whilst completely switched off,
take firm hold of the back part of the chuck and turn the
front part of the chuck counter clockwise.
- Insert the drill bit, screwdriver bit, or other tool/accessory
required for the task, into the chuck. In order to obtain a
secure fastening of the bit, insert the bit as far as you can
into the chuck. Take firm hold of the back part of the chuck
and turn the front part of the chuck clockwise until it is
firmly closed.
- In order to remove accessories from the chuck, follow the
same steps as indicated previously but in reverse order.
- Don't use rotation with hammering when the SDS-plus
adaptor + drill chuck is installed on the device.
How to select the direction of the rotation (Fig 1)
- Do not change the direction of the rotation whilst the tool
motor is in operation.
- The appliance has a selector (D), which allows the
direction of rotation to be changed.
Use:
- Connect the appliance to the mains.
- Place the appliance against the surface you want to work.
- Press the appliance until the lengthways play is taken up.
- Turn the appliance on, by using the on/off button (H).
Note: Exerting high pressure does not increase machine
effectiveness!
WARNING: When the bit begins to penetrate concrete or
comes up against the reinforcement rods in the concrete,
the tool may react dangerously. Make sure you keep your
balance by distributing your weight evenly and keeping
your feet in a safe position whilst holding the tool firmly in
both hands to avoid dangerous reactions.
- Select the appliance function desired.
Drilling and driving (wood, steel, ...) (Fig 1)
- Turn the selector (C) until points to (
- To drill or screw, ALWAYS have the direction set to
clockwise (CW).
- To unscrew, set the direction to counter clockwise
(CCW).
- The appliance should not be in use when changing the
screwing direction.
Hammer drilling with rotation
- Turn the selector (C) until points to (
Chiseling
- Turn the selector (C) until points to (
).
)
)
5