Ardo PE 58 SE 1P Manual De Utilización página 19

Under no circumstances use abrasive sponges or irritating
chemical detergents such as oven sprays or stain removers.
Use
Use the touch control system in the corresponding position
relative to the individual cooking needs. Keep in mind that the
higher the number, the more heat that it is produced.
Operation
A= ON/OFF button
B= Lock button
C= Lock button ON/OFF indicator light
D1= Slider control
D2= Cooking level indicator
E= Cooking zone selector button
F= Double zone selector button
G= Double cooking zone ON/OFF indicator light
I= "H" residual heat indicator symbol
L1= Rapid Heat up function ON/OFF button
L2= Heat up function active indicator light
N= Timer button
O= Timer adjustment (+ / -) buttons and Clock adjustment
buttons (+ / -)
P= Hotplates with timer function enabled indicator light
Q= Clock and Timer display
R= Cooking zone display
S= Timer and Clock area
Warning:
The first time the hob is switched on it will be in safety mode,
i.e. the "Lock button indicator light" (C) will be switched
on.
To use the hob, press and hold the Lock button (B) for 3
seconds, until the indicator light switches off.
Note: the Lock function is activated automatically every time
the power supply is cut off.
- The appliance can be switched on by selecting start-up
button A. A zero will appear on all displays for 10 seconds. If
no command is made within 10 seconds, the hob will switch
off again.
- Any of the cooking zones may be switched on by selecting
one of the corresponding 4 buttons (E). Once a cooking
zone has been selected, "0" will begin to flash on the display;
set the desired cooking level within 5/6 seconds using the
SLIDER control (D1).
- To set the cooking level, simply run your finger over the
SLIDER control.
Moving from "-" towards "+" will increase the temperature
level (D2) (from 1 to 9); to decrease it simply run your finger
from "+" towards "-".
The cooking level (e.g. 6) will appear on the cooking zone
display (R).
Note: you may also directly press any point on the SLIDER
control without running your finger along it; in this case the
temperature level corresponding to the point at which the
control was touched will be activated directly.
- To select the double cooking zone, where applicable, first
press button (E), then adjust the cooking level (D1) and press
the double zone selector button (F).
To deactivate the double zone, press button (E) followed
by button (F).
- There are several different ways of switching off a cooking
zone:
1- Select it and run your finger over the SLIDER control until
you reach "0".
2- Select it and directly press the "-" symbol on the SLIDER
control.
3- Press and hold the cooking zone selector button E for 3/4
seconds; it will then switch off automatically.
Note: when the hob is in operation and you press the SLIDER
control (D1), it will emit a sound alert (BEEP).
This sound alert informs the user that none of the cooking
zones (E) have been selected and therefore the temperature
level may not be altered.
- When a cooking zone (E) is switched to the OFF setting
and the temperature of the glass surface remains above
approximately 50°, the display (R) corresponding to that zone
will show a luminous signal alternating between "0" and "H". If
the hob is switched to the OFF setting (A), the luminous signal
will display the letter "H" in a fixed manner.
Warning:
To prevent damage being inflicted on the electronic circuits,
the hob is fitted with an overheating safety system.
In situations where cooking at a high power level has taken
place for an extended period of time, the hob may enter safety
mode and switch off automatically with no warning.
Once the temperature has returned to a safe level, the hob
may be switched on again.
Lock function
To prevent the hob from being used by children, all functions
may be locked by pressing the Lock button (B); this function
is active when the indicator light (C) is illuminated.
- The Lock function may be activated while the hob is switched
on or off.
- To activate or deactivate it, press and hold button (B) for
approximately two seconds.
- If the hob is switched on and the Lock function is enabled,
button A will still work.
O.S.D. (Overflow Safety Device)
- If any object has been placed on top of the control panel,
the hob will automatically revert to OFF mode.
Heat up L1 (Rapid heating)
The Heat up function can be used to set the cooking zone
to its maximum temperature for a specified period of time,
after which the temperature will return to a lower value set
previously.
To activate the Heat up function, select one of the cooking
zones (E).
Set the cooking level to "9" using the SLIDER control (D1) and
press the Heat up button (L1); the indicator light (L2) will
switch on and the letter "A" will appear on the cooking zone,
indicating that the Heat up function has been activated.
Set the desired cooking level (between 1 and 8); the cooking
zone display will now show the letter "A" and the desired
cooking level (e.g. 5) alternately.
- If the cooking level is not altered, the indicator light (D2)
will switch off and a BEEP will be emitted.
Note: the cooking level set previously may be increased or
decreased:
1- Select the cooking zone (E) for which the Heat up function
has been activated.
2- Set the desired temperature by running your finger over
the SLIDER control (D1).
When the Heat up function has finished running, the hob
- 18 -