Craftsman 917.28671 Manual Del Operador página 25

Si6N
lu tractor nuevo,
rendimiento y la
ucto de catidad.
continuacion:
nstrucciones de
caja de cart6n.
_rgada en forma
i forma c6moda
fladas en forma
fo, las llantas se
ica.)
segador est6
, de tado a lado
para obtener los
"teo (Las llantas
orma adecuada
_ulsi6n y de la
._corran el paso
3oleas y dentro
_-orreas.
: que todas las
guras y que los
rma adecuada.,
asegurese que
,. en la posict6n
a" (Yea "PARA
i6n de la Oper-
como usar su
tics puntos de
continuacion:
e llegar al nivet
te que estar fleno
r,nuevay limpia,
controles - su
_,relos antes de
; frenos est6 en
;egurao
la de Presencia
Funcionamiento
nodo adecuado
icionamiento y
af).
nsmisi6n antes
imera vez., Siga
pare el empiezo
EMPESAR EL
,R LA TRANS-
._OperaciSn de
TO REMOVE CABLES, REVERSE ORDER -
1, BLACK cable first from chassis and then
from the fully charged battery°
2. RED cable last from both batteries.
REPLACING BATTERY
_WARNtNG: Do not short battery terminals
by allowing a wrench or any other object to
contact both terminals at the same time,
Before connecting battery, remove metal
bracelets, wristwatch bands, rings, etc_
Positive terminal must be connected first to
prevent sparking from accidental grounding.
1. Lift hood to raised position,
2, Disconnect BLACK batter,/cable (A) then
RED battery cable and carefully remove
battery from tractor.
3. Install new battery withterminals in same
position as old battery,
4° First connect RED battery cable (B) to
positive (+) battery terminal with hex bolt
and keps nutas shown° Tighten securely.
Slide terminal cover (C) over terminal.
5, Connect BLACKgrounding cableto neg-
ative (-) battery terminal with remaining
hex bolt and keps nut, Tighten securely
6. Close hood°
Positive
(Red)
Cable
Negative
(Black)
Cable
ji
TO REPLACE HEADLIGHT BULB
1. Raise hood.
2. Remove bulb holder from the hole in the
backside of the grill.
3. Replace bulb in holder and install bulb
holder securely back into the hole in the
backside of the grill.
4. Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your
tractor to run poorly, stop running, or prevent
it from starting.
• Check wiring° See etectricalwiring diagram
in the Repair Parts manual.
TO REPLACE FUSE
Replace with 30 amp automotive-type plug-
in fuse. The fuse holder is located behind
the dash.
TO REMOVE HOOD & GRILL ASSEMBLY
1. Raise hood.
2. Unsnap headlight wire connector,
3. Stand in front of tractor. Grasp hood at
sides, tilt toward engine and lift off of
tractor.
4. When replacing hood, be sure to recon-
nect the headlight wire connector.
ood
Headlight
Wire
Connector
TRANSMISSION REMOVAL OR
REPLACEMENT
Should your transmission require removal for
service or replacement, it should be purged
after reinstallation and before operating the
tractor. See "PURGE TRANSMISSION" in
the Operation section of this manual.
ENGINE
TO ADJUST fHROTTLE CONTROL CABLE
The throttle control has been preset at
the factory and adjustment should not be
necessary Check adjustment as described
below before loosening cable. If adjustment
is necessary, see engine manual
TO ADJUST CHOKE CONTROL
The choke control has been preset at
the factory and adjustment should not be
necessary. If adjustment is necessary, see
engine manual,
TO ADJUST CARBURETOR
Your carburetor has been preset at the factory
and adjustment should not be necessary.
However, minor adjustment may be required
to compensate for differences in fuel, tem-
perature, altitude or load. If the engine does
need adjustment, see engine manual+
25