Team Electronic MX8 Mark-I Manual De Instrucciones página 7

English
TABLE OF CONTENTS
Setting up the TEAM MX8 Mark-I
1) Installation of a CB antenna
2) Aerial Connection
3) Installation in the car
4) Microphone DM-106S
5) Power source
Operation of the TEAM MX8 Mark-I
1) Switching on [ Vol / Off ] 15
2) Squelch [ SQ / Asq ] 15
3) Channel selection [  ] [  ]
4) Receipt tone selection Hi / Lo [ Mode ]
5) LCD background illumination [ DW / B ]
6) Modulation selection [ Mode ]
7) Version selection
8) Transmitting
9) Call tone
10) Priority Channel 9 [ CH9/19 ]
11) Channel scanning [ SC / KL ]
12) Dual watch function [ DW / B ]
13) Key lock function [ SC / KL ]
14) External speaker jack
15) External signal meter jack
Additional Information
1) Safety Instructions
2) General Precautions
3) Servicing
4) Conformity
Schematic Diagram
Channel Frequencies
Specifications
12
1) Installation of a CB antenna
The antenna is one of the most important parts of the equipment. The type of antenna and its
location has a great effect on the range of operation. Please consider the following criteria for
selecting the best location and inst allation of your antenna:
> Make sure that the antenna is designed for radio operation on 27 MHz.
13
> The location of the antenna should be as high as possible without any obst acles nearby.
13
> The aerial cable should not be damaged and the plugs should be properly connected.
13 - 14
> Make sure that the antenna cable is not bent too much.
14
> The bigger the mechanical size of the antenna, the higher the range of operation.
14
When you install a mobile antenna please note the following advices:
> The antenna should be fixed in the centre of a bigger p art of the coachwork.
> The mobile antenna coil should have the closest possible contact with a conducting metallic
surface of the bodywork of the car .
15
There are also some other possibilities to fix the antenna onto the car without the necessity
15
to drill a hole into the bodywork of your car , for example mounting the antenna onto the gut-
15 - 16
ter, mounting the antenna onto a holder on the cover of the boot or using an antenna with a
16
magnetic foot or using a windscreen antenna.
16
For base-station operation we recommend a st ationary antenna on the roof, for example the
17
TEAM ECO 050 or ECO 200.
17
17
> Please don't mount the CB antenna nearby a radio or TV antenna to prevent interference
17
of radio or TV reception.
17 - 18
> Keep an eye on power lines running along nearby when mounting the antenna on the roof.
18
" DANGER "
18
> The base-station antenna has to be connected via a lightning arrester .
18
> All connected cables including the antenna cable must not exceed a length of 3 m.
2) Aerial Connection
19
Before pressing the transmit key, a suitable aerial must be connected. The PL259 plug of the
19
aerial cable ( coax ) is connected to the SO239 socket ( 15 ) on the rear p anel. Make sure,
19
that all plugs are firmly tightened and properly soldered. Unsatisfactory connections can dam-
19
age the radio and will reduce the range of operation.
The antenna should be matched with the radio, otherwise a part of the transmit power will be
28 - 31
reflected at the antenna and will not be radiated. This causes also a drop in the range of oper-
54
ation. The matching can be carried out by a length adjustment of the antenna radial for a min-
55
imal SWR ratio which can be measured by a SWR meter ( e. g. TEAM SWR 1180P ). After
the measurement the SWR meter should be removed from the antenna line.
3) Installation in the car
When you want to fix the unit in your car , you can either fasten it with the help of the includ-
ed mounting bracket below the dashboard, or insert it into a car radio slot by using the includ-
ed inserting frame. Always mount the transceiver where the switches are easily accessible.
Other important points of view for the correct mounting position are:
Setting up the TEAM MX8 Mark-I
English
13