Lutron QSE-CI-DMX Instrucciones De Instalación Y Operación página 5

DMX Prog
RGB/CMY DMX
Push
Zone 4
Zone R to Assign
Zone L to Unassign
Programming (continued)
Zone 4- RGB/CMY
DMX
To unassign DMX channels from a GRAFIK Eye QS:
Zone 4
Component 1 channel
1. Enter programming mode on the QSE-CI-DMX: Press and hold
Choose Channel on
14
the programming button for 3 seconds. The "Status" LED will
DMX Prog
DMX AABB-CCEE
blink rapidly.
Push
14
2. The LEDs of the zones assigned to
Zone 4
Zone R to Assign
DMX channels will be flashing full on.
Zone L to Unassign
Channels 1,2,3
To unassign, press the desired zone's
Zone 4
on DMX AABB-CCDD
lower button. Press OK to confirm
operation.
Unassign?
Zone 4
RGB/CMY DMX
Choose Channel on
3. Exit programming mode: Press and hold the programming
Display type
DMX AABB-CCEE
button on the QSE-CI-DMX for 3 seconds. The yellow status
14
Set zones
LED will blink once per second.
Zone 4- RGB/CMY
Display Type Setup
Zone 4
Component 1 channel
There are two display types to choose from: "% display", which
displays light intensity as a percentage, and "0-255 display",
14
High end
which displays intensity as a numeric value. For RGB DMX
RGB/CMY DMX
zones, it may be desirable to select "0-255 display" in order to
Set zones
step through each entry in the RGB/CMY table. This option is Zone 4
available only after DMX channel assignment.
Channels 1,2,3
Zone 4- RGB/CMY
1. Enter programming mode on the GRAFIK Eye QS, and choose
on DMX AABB-CCDD
"Zone Setup" from the Main Menu. Select "Display type". The
Unassign?
Component 1 channel
RGB/CMY Config
LEDs of the zones assigned to DMX channels will be flashing full
on.
14
Master R/L
Display type
2. Use the zone raise/lower buttons to
toggle between display types for each
Enable
Set zones
Zone 4
zone. Press "OK" to confirm. Repeat
for all desired zones.
Channels 1,2,3
3. Exit programming mode.
on DMX AABB-CCDD
Unassign?
Trim Setup
High end
High and low end trim settings limit the maximum and minimum
output of a dimming zone. Follow the instructions below to
Set zones
Display type
manually set the levels, as desired.
Set zones
1. Enter programming mode on the GRAFIK Eye QS, and choose
"Zone Setup" from the Main Menu. Select "High end" or "Low
end". The LEDs of the zones assigned to DMX channels will
RGB/CMY Config
show the high end or low end intensity.
2. Use the zone raise/lower buttons to
Master R/L
High end
set the desired trim levels. Repeat for
Enable
Set zones
all desired zones and trims. Press OK
to confirm.
3. Exit programming mode.
Note: The "High end" and "Low end" trim can only be set if the
RGB/CMY Config
zone is assigned to at least one DMX channel.
Master R/L
Enable
Display type
Set zones
To enable/disable Master Raise/Lower from affecting
High end
RGB/CMY zones (disabled by default)
Set zones
1. After assigning RGB/CMY zones to the GRAFIK Eye QS, enter
programming mode on the GRAFIK Eye QS and choose "Zone
Setup" from the Main Menu.
Select "RGB/CMY config".
2. Use the Master Buttons to choose
RGB/CMY Config
"Enable" or "Disable". Press OK to
Master R/L confirm.
3. Exit programming mode.
Enable
Color Programming Tool
The QSE-CI-DMX comes with a standard table of colors already
loaded. Users can modify the table to achieve desired colors.
1. Install the program from the enclosed CD.
2. Create a new project, or use the provided default color table.
3. If you are creating a new project, you can enter individual color
values in either RGB (red-green-blue) or CMY (cyan-magenta-
yellow) format. Values can be entered in either decimal or
hexadecimal format. Additionally, the interpolate function will fill in
values automatically when you define the boundary values.
4. Use the "Test" feature on the title bar to view your edited color
table.
5. Connect a mini-USB cable between
7 5 1 8 6 1
9-16
1-8
OK
6. Use the "Transfer" command to
Mini-USB port
your PC and the mini-USB port
under the bottom hinged door of
your GRAFIK Eye QS.
either download your color table
into the QSE-CI-DMX, or to extract
a color table from a QSE-CI-DMX to
your PC for further editing.
5