Publicidad
Idiomas disponibles
Idiomas disponibles
the UP TIMER (9) and DOWN TIMER (8). Pressing the DOWN TIMER
(8) button until the timer display (7) shows "00" also deactivates the
timer function.
When the set time has elapsed, the selected cooking zone will
switch off and the timed zone indicator (6) and time indicator (7)
LEDs will illuminate intermittently while a warning beep will sound
for 1 minute. To cancel this acoustic warning before the set time has
elapsed, press any button on the touch control.
Cooking vessels (Fig. 3)
- a magnet-attracting vessel may be a suitable vessel for induction
cooking
- prefer vessels which are especially declared to be suitable for
induction cooking
- flat- and thickbottomed vessels
- a vessel with the same diameter as zones ensures the maximum
exploitation of power
- a smaller vessel reduces power exploitation, but does not cause
any energy loss We would anyhow not recommend the use of
vessels with diameters smaller than 10 cm.
- stainless-steel vessels with multi-layer or ferritic stainless-steel
bottoms when specifically suited for induction cooking
- cast-iron preferably enamel-bottomed vessels to avoid scratching
the pyroceram surface
- we do not recommend the use of any glass, ceramic, earthenware,
alluminium, copper or non-magnetic (austenitic) stainlesssteel
vessels.
Maintenance (Fig. 4)
Any remains of aluminium foil, food, fat, sugar or food with high
sugar content must be immediately removed from the hob surface
with a scraper to prevent potential damage to the hob surface.
Subsequently clean the surface with some towel and appropriate
product, rinse with water and dry by means of a clean cloth. Under
no circumstance should sponges or abrasive cloths be used; also
avoid using aggressive chemical detergents such as oven sprays and
spot removers.
Installer's Instructions
Installation
These Instructions are for the qualified technician, as a guide to
installation, adjustment and maintenance, according to the laws
and standards in force. These operations must always be carried out
when the appliance has been disconnected from the electric system.
Positioning (Fig. 5)
The fixture is especially designed for fitting into a work-top as shown
in the corresponding figure.
Place the supplied sealing agent along the hob perimeter.
Do not install the hob over an oven; in case you do, make sure of
the following:
- the oven is equipped with an appropriate cooling system
- there is no warm-air leakage from the oven towards the hob
- suitable air-inlets are provided as shown in the figure.
Electrical connection (Fig. 6)
Prior to carrying out the electrical connection, please ensure that:
- the plant characteristics are such as to follow what is indicated on
the matrix plate placed at the bottom of the working area;
- that the plant is fitted with an efficient earth connection, following
the standards and law provisions in force.
The earth connection is compulsory in terms of the law.
Should there be no cable and/or plug on the equipment, use suitable
absorption material for the working temperature as well, as indicated
on the matrix plate. Under no circumstance must the cable reach a
temperature above 50°C of the ambient temperature.
Power limitation function (only on certain models)
The appliance features a function that allows the maximum power
level to be limited internally. This maximum power level limit can be
selected from the following power values: 7,200 W, 6,000 W, 3,500 W
and 2,800 W. The appliance is configured by default to the maximum
power level limit.
To modify this factory setting, after connecting the appliance to the
power supply, with the touch control unlocked and all cooking zones
inactive, press simultaneously the UP (3) and DOWN (2) buttons at
the two ends of the touch control within 30 seconds of connecting
the power supply. The display will show the power level selected.
Use the UP (3) or DOWN (2) buttons on any cooking zone to select
one of the available values. Once the desired value is selected, press
simultaneously the UP (3) and DOWN (2) buttons at the two ends of
the touch control to memorise the power level limit and turn off the
touch control.
If when using the appliance a power level is selected that exceeds
the limit, the affected cooking zone display will show the symbol "r"
for 3 seconds and return to the previous power level.
To increase the power level on a given cooking zone, it may be
necessary to reduce the level on another cooking zone in order to
remain within the overall power limit.
Publicidad
