Publicidad
Idiomas disponibles
Idiomas disponibles
Automatic off
Once switched on, the touch control automatically switches
off after 20 seconds of inactivity. After selecting a cooking
zone, the automatic off time is divided into 10 seconds, after
which the zone is deselected and, after another 10 seconds,
the touch control switches off.
Switching a cooking zone on/off
If the touch control is switched on, the cooking zone can
be selected by pressing the button (5) of the corresponding
zone.
The display (6) of the zone selected lights up, while the re-
maining displays are dimmed. if the cooking zone is "hot",
"H" and "0" are alternately displayed.
Press the PLUS (3) or MINUS (2) button to select a setting
and the zone will begin to heat up.
Once the cooking zone has been selected, the setting can
be selected by keeping the PLUS (3) button pressed down.
The setting begins at level 1 and increases by 1 level every
0.4 seconds. When setting "9" is reached, the setting will
not be changed further.
If the setting level has been selected using the MINUS (2)
button, the start level is "9" (maximum level). Keep the
button pressed down to lower the active level by 1 every
0.4 seconds. When setting "0" is reached, there will be no
further setting changed. The setting can only be changed by
pressing the MINUS (2) or PLUS (3) button again.
Switching a cooking zone off
Select the zone to be switched off using the corresponding
button (5). The display (6) of the zone selected lights up,
while the remaining displays are dimmed. Press the PLUS
(3) and MINUS (2) buttons at the same time and the setting
level of the zone is changed to 0. Alternatively, the MINUS
button (2) can be used to reduce the setting level to 0.
If a cooking zone is "hot", "H" and "0" will be alternately
displayed.
Switching all cooking zones off
Press the ON/OFF (1) button to immediately switch off all
zones at any time. In standby mode, an "H" is displayed in
all cooking zones that are "hot". The remaining displays will
be switched off.
Setting level
The cooking zone can be set to 9 levels that are indicated
by the numbers "1" to "9" on the seven-segment LED dis-
plays (6).
Residual heat indicator
This informs the user that the glass is at a dangerous tem-
perature in the event of touching the area located around
the cooking zone. The temperature is determined by a
mathematical model and any residual heat is indicated by a
"H" on the corresponding 7-segment display.
Heating and cooling are calculated based on:
· The selected setting level (between "0" and "9")
· The ON/OFF time.
After switching off the cooking zone, the corresponding dis-
play will indicate "H" until the temperature in the zone has
dropped below the critical level (≤ 60°C).
Automatic off function (operating time limitation)
In terms of the setting level, if no operation occurs each coo-
king zone switches off after an established maximum time.
Each operation in the cooking zone condition (using the
PLUS (3) and MINUS (2) or dual zone) restarts the maximum
operating time of the zone by resetting it to its initial value.
Protection against unintended switching on
· If the electronic control detects a button being held down
for approx. 10 sec. it will switch off automatically. The con-
trol sends out an audible error signal to warn the user that
the sensors have detected the presence of an object. The
displays indicate error code " E R 0 3 ". If the cooking zone
is in "hot" mode, "H" will be indicated alternately on the
display with the error signal.
· If no cooking zone is activated within 20 seconds after
switching on the touch control, it will return to standby
mode.
· When the control is switched on, the ON/OFF button has
priority over all other button and, therefore, the control can
be switched off at any time, even when several buttons are
pressed at the same time or a button is kept held down.
· In standby mode, no effect will be caused by buttons being
kept held down. However, before the electronic control can
be switched back on, it has to detect that no button is pres-
sed down.
Button lock (child safety feature)
• Child safety feature:
Button lock:
To activate the child safety feature after having switched on
the Touch control, press de rear left cooking zone selection
button at the same time as the MINUS button (2) for 3 se-
conds, followed by just the rear left cooking zone selection
button. An "L" standing for LOCKED (child safety feature
preventing unintended switch on) will be indicated on all
displays. If a cooking zone is in "hot" mode, "L" and "H" will
be alternately displayed.
This operation must take place within a 10 successive se-
conds and no button other than those described must be
pressed. Otherwise, the sequence will be interrupted and
the hob will not be locked.
The electronic control remains locked until it unlocked by
the user, even if it has been switched off and back on mean-
while. Not even touch control resetting (after a voltage drop)
will interrupt the button lock.
Cancelling the button lock:
After switching the touch control on, the child safety feature
can be disabled. Press the rear left cooking zone selection
button and the MINUS button (2) for 3 seconds, followed by
Publicidad
