Technical Characteristics; Diagnostics Led - tau K100M Guía Para La Instalación

Ocultar thumbs Ver también para K100M:

Guía para la instalación (21 páginas)

Contenido

Tabla de contenido

Idiomas disponibles

MANUFACTURER'S DECLARATION OF INCORPORATION

(in accordance with European Directive 2006/42/EC App. II.B)

Manufacturer:

Address:

Declares under its sole responsibility, that the product:

designed for automatic movement of:

for use in a:

complete with:

Model:

Type:

Serial number:

Commercial name:

Has been produced for incorporation on an access point (swing gate) of for assembly with other devices used to move such an access point, to constitute a machine

in accordance with the Machinery Directive 2006/42/EC.

Also declares that this product complies with the essential safety requirements of the following EEC directives:

2014/35/EU Low Voltage Directive

2014/30/EU Electromagnetic Compatibility Directive

and, where required, with the Directive:

2014/53/EU Radio equipment and telecommunications terminal equipment

Also declares that it is not permitted to start up the machine until the machine in which it is incorporated or of which it will be a component has been identified

with the relative declaration of conformity with the provisions of Directive 2006/42/EC.

The following standards and technical specifications are applied:

EN 61000-6-2;

EN 61000-6-3;

EN 60335-1;

ETSI EN 301 489-1 V1.9.2;

EN 60335-2-103;

The manufacturer undertakes to provide, on sufficiently motivated request by national authorities, all information pertinent to the quasi-machinery.

Sandrigo, 08/11/2016

Name and address of person authorised to draw up all pertinent technical documentation:

Loris Virgilio Danieli - via E. Fermi, 43 - 36066 Sandrigo (Vi) Italy

Dip-switches

SENS

TCA

DL3

PHOTO

DL4

CLOSE LIMIT SWITCH

DL5

OPEN LIMIT SWITCH

DL6

STOP

K100M

DL2

OPEN/CLOSE

DL1

RADIO CONTROLS

TAU S.r.l.

Via E. Fermi, 43

36066 Sandrigo (Vi)

ITALY

Electronic control unit

Swing gate

General environment

Radioreceiver

K100M

see silver label

Control panel for T-ONE5E gearmotor

ETSI EN 301 489-3 V1.6.1;

EN 300 220-2 V2.4.1;

Legal Representative

_________________________________________

Loris Virgilio Danieli

Antenna

Photocells

1 2

Photocell - 24 V AC

0 V AC

Common

Photocell (N.C.)

SENS

Stop

TCA

DL3

Open/Close

RESET

DL4

DL5

OP/CL

DL6

Flashing

DL2

RADIO

light

DL1

230 V AC

max. 50W

Phase

Neutral

K100M

Control panel for T-ONE5E gearmotor

GB - Translation of original instructions

D_MNL0K100M 05-05-2017 - Rev.08

WARNING!

Attention: This product may only be installed from professional installers. Only qualified and trained electricians may connect, programme and

service the controls.

No information given in this manual can be considered as being of interest to end users.

This manual is enclosed with control unit K100M and may therefore not be used for different products!

Important information:

Disconnect electric power to the system before making maintenance, repairs or removing covers

The K100M control unit has been designed to control a electromechanical sliding door operator.

Any other use is considered improper and is consequently forbidden by current laws.

Read all instructions carefully and completely before attempting to install and use this automatic gate operator!

INSTALLATION

Make sure the gate has been properly installed and slides freely in both directions. Repair or replace all worn or damaged gate hardware prior

to installation. A freely moving gate will require less force to operate and will enhance the performance of the operator and safety devices used

with the system.

Also check that the gate operator assembly has been installed according to the instructions.

WARNING: The automatic gate operator must be grounded - All Federal, State and local safety codes must be observed.

ATTENTION:

do not use solid wire, use only multi threaded wire

do not reuse pre-existing electric wire.

IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED THE "MANUFACTURER" SHALL IN NO EVENT BE LIABLE FOR DIRECT, INDIRECT, INCI-

DENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS WHETHER BASED IN CONTRACT TORT OR ANY OTHER LEGAL

THEORY DURING THE COURSE OF THE WARRANTY OR AT ANY TIME THEREAFTER.

CONTROL PANEL FOR ONE 230 V AC MOTOR

MICROPROCESSOR-CONTROLLED LOGIC



STATUS LEDS



LINE FUSE



BUILT-IN FLASHING LIGHT CIRCUIT

BUILT-IN 433.92 MHz RADIO RECEIVER



MAX. OPERATING TIME 96"



AUTOMATIC 50 / 60 HZ FREQUENCY DETECTION



ADJUSTABLE SOFT-STOP

AMPEROMETRIC OBSTACLE DETECTION



1 2 3 4 5

TESTING

Once the connection has been completed:

 All the green LEDs must be ON (each of them corresponds to a Normally Closed input). They will turn OFF when the controls to which they are as-

sociated are operated.

 The opening control red LED must be switched OFF (corresponding to a Normally Open input), it comes ON only when the control it is associated with

is involved; the DL1 red LED must be steady ON.