Gemini UX-1600 Manual De Funcionamiento página 3

1. Open the battery holder. Insert 2 AA batteries into the battery holder
according to the polarity indication marked on the battery housing.
Close the battery holder.
2. Push the power switch to the ON position. The BATT indicator should
flash once briefly as you turn on the mic. This indicates that the mic has
sufficient power. If BATT stays on, it indicates that the batteries have
insufficient power and should be changed. If BATT does not light at all
and the mic does not work, it indicates that the batteries are either dead
or not positioned correctly. Correct the positioning or change the
batteries. If the microphone is not going to be used for any length of
time, push the power switch to OFF and remove the batteries. Do not
switch the mic on and off rapidly as you will not receive a true BATT
indicator reading.
• Heavy duty strain relief.
• Foam wind screen.
• Tie clip.
Note: The lavalier mic clip should be placed on the center of your
shirt just below your collarbone.
• Heavy duty strain relief.
• Headset.
• Foam wind screen.
1. Open the battery door by sliding towards the arrow. Insert 2 AA
batteries into the battery holder as shown on the battery housing.
Close the battery door.
2. Connect the mic to the belt pack transmitter.
3. Push the power switch to the ON position. The LOW BATT indicator
should flash once as you switch on the belt pack indicating that the
transmitter has sufficient power. If LOW BATT stays on, it indicates
that the batteries have insufficient power and should be changed. If
the LOW BATT does not light at all, it indicates that the batteries are
either dead or not positioned correctly. Correct the positioning or
change the batteries. If the transmitter is not going to be used for any
length of time, push the power switch to OFF and remove the batteries.
4. To adjust the gain (input sensitivity), place the small plastic tool
(included with the unit) in the hole marked GAIN on the side of the
belt pack. Slowly turn the tool and speak into the mic until the volume
is at the desired level. Use of any other tool to adjust the gain will
void the warranty.
Hint: If the audio signal is distorted, try turning the gain down on
your belt pack transmitter and/or your mixer and increasing the
volume output on the receiver.
USA
Frequency Range..........................................................790.375~805.375 MHz
Receiving System..................................................................PLL Synthesized
Receiving Mode........................................................................single channel
Frequency Stability.............................................................................± 0.005%
Signal to Noise Ratio...............> 94 dB @ 15 kHz and 60 dBµV antenna input
Dynamic Range......................................................................................> 96dB
AF Response..............................................................40 Hz - 15 kHz (±3 dB)
T.H.D..................................................................................< 1.0% @ 1 kHz
Audio Output..............................................unbalanced; 0 dB (0 dB=0.775V)
Power Supply.........................................................................DC 12~18 V
Dimensions........................2" (H) x 8.27" (W) x 6.5" (D) (51 x 210 x 166 mm)
Frequency Range.........................................................790.375~805.375 MHz
RF Power Output.........................................................................30 mW max.
Oscillation Mode.............................................................PLL Synthesized
Frequency Stability............................................................................± 0.005%
T.H.D.......................................................................................< 0.5% @ 1 kHz
LED Indicator...............................................Power ON-OFF and low battery
Current Consumption..........................................................65 mA @ 2.4V
Batteries....................................................................................................2 AA
Microphone Element..........................................................................Dynamic
Dimensions................................................10.7" (L) x 2.4" (D) (272 x 62 mm)
Microphone Element........................................................................Condenser
Dimensions...................................4" (H) x 2.6" (W) x 1" (D) (98 x 66 x 25 mm)
Page 3
at 48 kHz reference RF deviation
balanced; -20 dB (0 dB=0.775V)
USA