Publicidad
Idiomas disponibles
Idiomas disponibles
FLUSH Flange Carpet Installation – FLUSH (shown): Open Cover and turn four Jack Screws to raise Flush Flange with
Cover flush to surface of Carpet floor.
Figure F
Pour Depth
See Table
and refer
to Fig. 6.
Carpet Flooring
Floor Box
Pour Depth
Flush Flange With Cover
CFB2G25, xxCR
3.0"
24GTCVRxx
CFB2G30, xxCR
3-1/2"
24GTCVRxx
ATTACHING THE COVER: 24GCCVRxx rectangular cover assembly shown
•
NOTICE: Use only electrical grade type RTV silicone sealant to insure scrub water tightness.
•
Slide Gasket to underneath of Flat Flange or apply bead of Silicone compound as shown depending on application Tile or Carpet.
•
Pull and Lift Cover upright at 90° as shown to access Jack Screws.
•
Attach cover assembly to top mounting plate using jack screws [7]. Fasten until flange is level and secure to floor.
•
To adjust cover assembly turn jack screws [7] counter clockwise to raise or clockwise to lower. Sequentially turn four jack screws as needed for proper
leveling of flange to floor. The jack screws have a 1 inch maximum adjustment.
Pull
Figure 7
Jack Screw (4x)
7
PD2523
(Page 6)
08/16
Apply Grout
or
Silicone
Carpet
compound.
Cover
Flat Flange (shown)
Gasket
Flat Flange
Pre-assembled Locknut
Jack Screw (4x)
After Concrete Pour Box installation:
To attach
CAUTION: Temporary concrete covers are intended to keep
Flush
concrete residue from entering box during pour and are not
Flange,
See Fig. 7.
Cover
intended to support loads. Replace with permanent flange/
cover immediately after concrete has hardened or temporarily
reinstall concrete metal cover [4].
8. After concrete has hardened, remove temporary concrete
metal cover [4] and plastic cover [5]. Retain these temporary
covers.
9. Use wiring channel [6] for feed through. Wiring channel areas
given in Table 1. (Wiring channel must be removed for feed
through applications.)
Jack
10. Pull and dress wires.
Screws
11. Reinstall wiring channel. Align with notches [2]
12. Consult
electrical
instructions for wiring device installation.
13. Attach Flange with Cover (see Figure 7). For desired flange
styles see Figures A,B,C,D,E or F.
Ensure to set height of the top of the box (Figure 6) with plastic
cover [5] or without plastic cover (Figure 5) as indicated. See
Figures A, B, C, D, E, or F with tables for desired floor finish.
Figure 5
WITHOUT PLASTIC COVER
Pour concrete flush to Top Plate
Remove plastic cover
and tape all holes and seams
Applications:
Ceramic Tile (See Fig. A, Fig. B or Fig. C)
Laminate Flooring (See Fig. A, Fig. B or Fig. C
Carpet Flooring with Flat Flange (See Fig. E)
VCT with Flat Flange (1/8" Min. Thick. See Fig. B)
PD2523
(Page 3)
CFB2G25, CFB2G25CR
CFB2G30, CFB2G30CR
device
mounting
plate
installation
Figure 6
Pour concrete flush to Top Plate
4
Temporary concrete
metal cover
Applications:
Finished Concrete with Flush Flange (See Fig. D)
VCT with Flush Flange (See Fig. D)
Carpet Flooring with Flat Flange (See Fig. F)
08/16
Table 1
Catalog No.
Wiring Channel Areas
(1) 0.357 in² [230,3mm²]
(1) 0.826 in² [532,9mm²]
WITH PLASTIC COVER
5
Additional ½"
Publicidad
