DeVilbiss IntelliPAP AutoBilevel CPAP DV57 Serie Guía De Instrucciones página 21

Display Example
Max IPAP
15.0 cmH2O
Min EPAP
5.0 cmH2O
Pressure Support
5.0 cmH2O
IPAP
10.0 cmH2O r 5.0
EPAP
5.0 cmH2O r 5.0
Set Pressure
10.0 cmH2O
Delay Time
20 minutes
Delay Pressure
4.0 cmH2O
IPAP Rounding
3 (1234 ms)
EPAP Rounding
3 (1234 ms)
Insp. Trigger
5
Exp. Trigger
5
Tubing Length
1.8 m (6 ft)
SmartFlex Menu
Press 
Enable Menu
Press 
LCD Contrast Adj
50 %
Compliance Meter
123456.7 hours
A-DV57
Description
Maximum IPAP pressure level that will be administered. Range: (Min
EPAP + Pressure Support) - 25.0 cm H
Minimum EPAP pressure level that will be administered. Range: 3.0 cm
H 0 - (max IPAP - Pressure Support), increments of 0.5 cm H
2
Difference between IPAP and EPAP Pressure. Range: 0 - (Max IPAP -
Min EPAP), 12 cm H
This is a prescription setting which controls the pressure during inhale,
this also shows the pressure delta (5.0 in example) between inhale and
exhale pressure settings
This is a prescription setting which controls the pressure during exhale,
this also shows the pressure delta (5.0 in example) between inhale and
exhale pressure settings
This is a prescription setting which controls the operating pressure.
Selectable delay time setting. Your provider has set the delay time.

This is a prescription setting which controls the operating pressure
during the delay time.
This is a setting which controls the comfort rounding when switching to

IPAP pressure, settings are 0 thru 5 also shows measured rise time of
the last breath in milliseconds.
This is a setting which controls the comfort rounding when switching to

EPAP pressure, settings are 0 thru 5 also shows measured rise time of
the last breath in milliseconds.
This is a setting which controls the sensitivity of the inspiratory trigger,

can be set from 1 to 10, 1 is most sensitive, 10 is least sensitive.
This is a setting which controls the sensitivity of the expiratory trigger,

can be set from 1 to 10, 1 is most sensitive, 10 is least sensitive.
The standard tubing length supplied with the device is 6 feet (1.8

meters). However, you can adjust your IntelliPAP to accommodate an air
supply tubing length of 10 feet (3.0 meters). Replacement tubing can be
obtained through your home care provider (part numbers listed at the
end of this manual).
Pressing the down key enters the SmartFlex menu. Refer to SmartFlex
Menu section for details
Pressing the down key enters the Enable menu. Refer to next section for
Enable Menu details.
This setting changes the contrast for the LCD display. This only needs to
be adjusted if you find it difficult to see the display from your viewing
angle.
The total number of hours (in 1/10 hour increments) that the IntelliPAP
has been providing therapy.
O, increments of 0.5 cm H
2
O max, increments of 0.5 cm H
2
AutoBilevel
O.
2
AutoBilevel
O
2
AutoBilevel
O
2
CPAP Mode
CPAP Mode
Mode
Mode
Mode
Mode
Bilevel S
Modes
Bilevel S
Modes
All
All
All
Bilevel
Modes
All
Bilevel
Modes
All
Bilevel
Modes
All
Bilevel
Modes
All
All
All
All
eN - 21