Hoover XARION Manual De Instrucciones página 4

USING YOUR CLEANER
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [5]
2. Adjust the telescopic tube to the desired height by holding the handle and moving
the telescopic tube adjuster up or down. [6]
3. Select carpet care control height by pressing the pedal in the nozzle. [7]
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
Switch the cleaner on by pressing the On/Off Button on the cleaner main body. [8]
4.
Adjust the suction by sliding the suction control to the desired level. [9]
5.
6. Switch off at the end of use by pressing the On/Off Button. Unplug and press the
cord rewind button to wind the power cord back into the cleaner. [10]
7. To store your cleaner adjust telescopic tube to the lowest height setting and park the
nozzle in the park position on the cleaner main body. [11]
ACCESSORIES
All accessories can be fitted to the end of the handle or the end of the telescopic tube.
3 in 1 tool* – Combines several functions in one, with maximum flexibility by the rotating
body. Reach into awkward areas by rotating the body. The 3 in 1 tool can be stored neatly
underneath the hose handle.[1] (Depending on model)
Crevice Tool* – For corners and hard to reach areas. [12]
Furniture Nozzle* – For soft furniture and fabrics.[13]
Dusting Brush* – For bookshelves, frames, keyboards and other delicate areas. To
extend the brushes push the button on the body of the tool. [14]
Parquet Nozzle* – For parquet floors and other delicate floors. [1X]
Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1W]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [1U]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas, particularly suitable for aller-
gen removal. [1V]
IMPORTANT: Do not use the turbo and mini turbo nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while
brush is rotating.
4800xxxx Xarion Pro Standard handle ML ef.indd 2
CLEANER MAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator in the container empty the dust container.
IMPORTANT:To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Release the container carry handle by lifting the centre latch to detach the dust
container from the main cleaner and pull upward to remove. [15]
2. Hold the dust container over a bin with one hand and with the other pull the dust
container catch to open the door and empty. [16]
3. Close the dust container door and refit to the cleaner main body. To lock in place
push the container carry handle down until the latch connects with the main body
of the cleaner. Once correctly retained the carry handle will sits flush with the top
of the cleaner.
Cleaning the washable filters
The cleaner is fitted with a filter pack. To maintain optimum cleaning performance regu-
larly remove the the filters and tap against the side of the bin to release dust.The filters
should be washed every 3 months or when the filter has excessive dust level.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean
your filters may result in air blockage, overheating and product failure. This may
invalidate your guarantee.
IMPORTANT: Regularly check and maintain the filters.
IMPORTANT: Always ensure the filter pack is fully dry before use.
To access the Pre- Motor filter:
NOTE: Ensure the carry handle is at its down position before opening the filter door.
1. Unlock the filter door by pulling the filter latch upwards. Open the filter door. [17]
2. Remove the blue filter pack by pressing down on the retainer catch to release. The
filter pack will pop up. Slide the filter pack out. [18]
3. Unlatch the filter pack frame.
4. Remove the micro filter from the pack frame and wash the micro filter by handusing
warm water. Do not use hot water or detergents. Remove excess water from the
filter and leave to dry fully before reusing. [21]
5. Reassemble to filter pack once fully dry and refit to the cleaner. Press on the top of
the filter to ensure it clips back into place.
2
GB
(*Certain Models Only)
25/01/2011 10:36:28