Publicidad
Idiomas disponibles
Idiomas disponibles
Before using the heater, read and understand all instructions and follow them carefully. The manufacturer is not responsible for
GENERAL RECOMMENDATIONS
Heaters are to be run on heating with oil and kerosene.
They heaters produce warm air mixed with combustion gases.
Always follow local ordinances and codes when using this heater.
• read and follow this owner's manual before using the heater.
• use only in places free of flammable vapours or high dust con-
tent.
• never use heater in immediate proximity of flammable materials.
Minimum clearance 2,50 m.
• make sure fire fighting equipment is readily available.
• make sure sufficient fresh outside air is provided according to
the heater requirements. They should only be used in well venti-
lated areas in order to avoid carbon monoxide poisoning.
• never block air inlet (rear) or air outlet (front).
• in case of very low temperatures add kerosene to the heating oil.
• make sure heater is always under surveillance and keep children
and animals away from it.
• before starting the heater always check free rotation of ventilator.
• unplug heater when not in use.
OPERATION
Before any attempt of starting the heater is made, check that your
electrical supply conforms to the data on the model plate.
Warning
Mains must be fitted with a thermo-magnetic differren-
tial switch.
Unit plug must be linked to a socket with a mains
switch.
The heater can run automatically when connected to a control de-
vice such as thermostat, time clock. Connection of controller is made
through cable protection (16) according to wiring diagram on page 19.
To start heater, connect to mains, set control device at desired val-
ue, set switch (14) on position
: the ventilator starts, immediately fol-
lowed by ignition. When unit is started for the first time or is started af-
ter the oil tank has been totally emptied, the flow of oil to the burner
may be impaired by air in the circuit. In this case the control box will
cut out the heater and it might be necessary to renew the starting pro-
cedure once or twice by depressing the button (14) in on position "0"
and pressing the button in the position
Should the heater not start, check that oil tank is full. Press the
button on position "0" and restat the space heater pressing the button
on position
.
Should the heater still not work, please refer to chapter "OB-
SERVED FAULTS, CAUSES AND REMEDIES".
Warning
If the voltage supply is less than 190 V, the space heater
automatically stops and the lamp flashes. The space
heater can automatically restart when the voltage goes
up again to 205 V.
STOPPING THE HEATER
Set main switch (14) on "0" position or turn thermostat or other
control device on lowest setting.
SAFETY DEVICES
The unit is fitted with an electronic flame control box. In case of
malfunction this box will cut in and stop the heater, in the control box
reset button (14) will light up.
You will have to depress button (14) in the position "0" on control
box before being able to restart the heater.
IMPORTANT
damages to goods or persons due to improper use of units.
.
2
TRANSPORT
Warning
Before making any attempt to restart heater find and
eliminate reason of overheating.
Before heater is moved it must be stopped and unplugged. Before
moving the heater wait till it has totally cooled off and make sure oil
tank cap is securely fixed.
GE 20 heaters with wheels must be wheeled.
MAINTENANCE
Preventive and regular maintenance will ensure a long trouble free
life to your heater.
Warning
Never service heater while it is plugged in, operating or
hot.
Severe burns or electrical shock can occur.
Every 50 hours of operation: wash the filter with clean oil, or, if too
dirty, replace it, remove upper body parts and clean inside and ventila-
tor with compressed air, check correct attachment of H.T. connectors
to the electrodes and check H.T. cables, remove burner assembly, clean
and check electrode settings, adjust according to Fig.2.
Fig.2
GB
2,5 - 3 mm
2-3 mm
Publicidad
