GEA ZET1P Instrucciones De Instalación

GEA ZET1P Instrucciones De Instalación

Hornos de pared eléctricos empotrados

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation Instructions
27" & 30" Electric Built-In Wall Ovens
Questions?
Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
Save these instructions
for local inspector's use.
Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with Consumer.
ATTENTION INSTALLER:
All electric wall ovens must be hard-wired (direct-wired) into an
approved junction box. A plug and receptacle is NOT permitted on these products.
FOR YOUR SAFETY:
WARNING:
Before beginning the installation, switch power off at the service panel and
lock the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
(up to 200°F [93.3°C]) generated by the oven.
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2" Conduit
1
REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all packing
parts from oven, racks and heating elements. Remove protective film and labels on the outer door
and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping
screws securing the oven to the base pad. Open oven door and remove literature pack and oven
racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation
process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from
seperate box and set aside (30" Double Wall Ovens Only).
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance
requires a qualified installer or electrician.
• Proper installation is the responsibility
of the installer.
• Product failure due to improper installation
is not covered under Warranty.
• Product is for indoor use only.
TOOLS YOU MAY NEED
1/8" Drill Bit and Electric or Hand Drill
T20 Screwdriver
Phillips Screwdriver
Wire Strippers
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also
be installed below a countertop or below specified cooktops. See the label on top of the oven for approved
models.
DOUBLE OVEN INSTALLATIONS
A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the
oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for specific
requirements.
2
PREPARE THE OPENING
NOTE: If the cabinet does not have a solid bottom, two
braces or runners must be installed to support the weight
of the oven. For single ovens, the runners and braces
must support 220 lbs (99 kg). For double ovens, the
runners and braces must support 400 lbs. (181 kg).
NOTE: If marks, blemishes or the cutout opening are
visible above the installed oven, it may be necessary to
add wood shims under the runners and front trim until
the marks or opening are covered.
NOTE: If the cabinet does not have a front frame and
the sides are less than ¾" (1.9 cm) thick, shim both sides
equally to establish the cutout width.
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
C
L
Suitable
Bracing
to Support

Publicidad

Tabla de contenido
loading

Resumen de contenidos para GEA ZET1P

  • Página 1 Installation Instructions DESIGN INFORMATION 27” & 30” Electric Built-In Wall Ovens SINGLE OVEN INSTALLATIONS The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also be installed below a countertop or below specified cooktops. See the label on top of the oven for approved Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com models.
  • Página 2 Unit Overlap Top 1” (2.5 cm) 1” (2.5 cm) Drawers, Walls, etc., ” (3.2 cm) for PT9050 When Door Is Open ZET1S and ZET1P) Overlap of Oven 1” (2.5 cm) min. 1” (2.5 cm) min. Unit Overlap Bottom 1” (2.5 cm) ”...
  • Página 3 Height to Bottom 44” (111.8 cm) 47” (119.4 cm) 47” (119.4 cm) of Junction Box Recommended ” (33.7 cm) 12” (30.5 cm) 12” (30.5 cm) Cutout Location from Floor Continue to Section 3. 31-11043 08-16 GEA...
  • Página 4 PEDESTAL RAIL INSTALLATION (30” DOUBLE OVENS ONLY) A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom flush with side of cabinet opening. Locate each rail so that front of rail is behind front cabinet opening.
  • Página 5: Electrical Requirements

    DOOR REMOVAL (RECOMMENDED) ELECTRICAL REQUIREMENTS (CONT.) This appliance must be supplied with the proper voltage and frequency and connected to an individual, NOTE: Door removal is not a requirement for installation of the product but is an added convenience. properly grounded branch circuit, protected by a circuit breaker or fuse. See the rating plate located on the To remove the door: oven frame to determine the rating of the product.
  • Página 6: Make Electrical Connections

    MAKE ELECTRICAL CONNECTIONS FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION WARNING: NOTE: If residence leads are aluminum conductors, see WARNING in Section 5, Electrical Requirements. Switch power off at the service panel and lock the service disconnecting When connecting to a four-conductor branch circuit, if local codes permit: means to prevent power from being switched on accidentally.
  • Página 7: Mount The Oven

    DWO’s with pedestals IMPORTANT: If this unit is ever removed from the cabinet or the oven is ever pulled out for service, the bottom trim must be removed first or damage to the trim will occur. 31-11043 08-16 GEA...
  • Página 8: Replacing The Oven Door

    OVEN RACK GUIDE INSTALLATION (IF APPLICABLE) REPLACING THE OVEN DOOR A. Locate included oven rack guide mouting hardware. NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. B.
  • Página 9 H Depth - side and top cleats 2-1/2 2-1/2 2-1/2 2-1/2 Electrical J Vertical from upper right corner 5-1/4 5-1/4 5-1/4 5-1/4 Junction Box K Horizontal from upper right corner 9-1/2 9-1/2 9-1/2 9-1/2 All dimensions shown are in inches. 31-11087-1 05-17 GEA...
  • Página 10 Instrucciones de instalación Hornos de pared eléctricos empotrados de 27” y 30” INSTALACIONES DE HORNO ÚNICO El horno único puede instalarse solo en un gabinete o sobre un cajón calentador. El horno único también puede instalarse debajo de un mostrador de encimera o debajo de las estufas especificadas. Vea la ¿Preguntas? Llame al 1.800.GE.CARES (1.800.432.2737) o visite GEAppliances.com etiqueta de la parte superior del horno para consultar los modelos aprobados.
  • Página 11 1” (2,5 cm) 1” (2,5 cm) está abierta unidad en parte superior ” (3.2 cm) para PT9050, ZET1S y ZET1P) Superposición de la 1” (2,5 cm) mín. 1” (2,5 cm) mín. parte superior del horno ” (3.2 cm) para PT9050, Superposición de la...
  • Página 12: Dabertura Para Instalación Sobre Un Cajón Calentador

    44” (111,8 cm) 47” (119,4 cm) 47” (119,4 cm) inferior de la caja de conexiones Ubicación ” (33,7 cm) 12” (30,5 cm) 12” (30,5 cm) recomendada de la abertura desde el piso Continúe en la sección 3. 31-11043 08-16 GEA...
  • Página 13 INSTALACIÓN DEL RIEL CON PEDESTAL (30” HORNOS DOBLES ÚNICAMENTE) A. Coloque un riel con pedestal en cada rodadura del gabinete o centrado en el lado opuesto de la parte inferior del gabinete sólido nivelado con el lateral de la abertura del gabinete. Ubique cada riel de modo que la parte frontal de los mismos se encuentre detrás del lado frontal de la abertura del gabinete.
  • Página 14: Remoción De La Puerta (Recomendada)

    REMOCIÓN DE LA PUERTA (recomendada) REQUISITOS ELÉCTRICOS (CONT.) Este aparato debe recibir el voltaje y frecuencia adecuados, y debe conectarse a un circuito derivado NOTA: La remoción de la puerta no es un requerimiento de la instalación del producto, pero es una individual con adecuada conexión a tierra, protegido por un interruptor de circuitos o fusible.
  • Página 15: Realice Las Conexiones Eléctricas

    REALICE LAS CONEXIONES ELÉCTRICAS CONEXIÓN DE CIRCUITO DERIVADO DE CUATRO CONDUCTORES ADVERTENCIA: Desconecte la energía del panel de servicio y bloquee los medios NOTA: Si los cables domésticos son conductores de aluminio, ver la ADVERTENCIA de la sección 5, de desconexión para evitar el accionamiento de la energía de manera accidental. Cuando los medios Requisitos eléctricos.
  • Página 16: Instale El Horno

    B. Asegure el gabinete del horno con los tornillos provistos. DWO sin pedestales IMPORTANTE: Si esta unidad alguna vez se quita del gabinete o si el horno se quita de servicio, el reborde inferior debe quitarse antes o el reborde sufrirá daños. 31-11043 08-16 GEA...
  • Página 17: Cómo Volver A Colocar La Puerta Del Horno

    GUÍA DE INSTALACIÓN DE LA ESTANTERÍA DEL HORNO (SI CÓMO VOLVER A COLOCAR LA PUERTA DEL HORNO CORRESPONDE) NOTA: La puerta del horno es pesada. Puede necesitar ayuda para levantar la puerta lo suficiente como para deslizarla dentro de las ranuras de la bisagra. No levante la puerta de la manija. A.
  • Página 18: Materiales Adicionales Que Necesitará

    H Profundidad – ristreles lateral y superior 2-1/2 2-1/2 2-1/2 2-1/2 Caja de Empalmes Vertical desde la esquina superior derecha 5-1/4 5-1/4 5-1/4 5-1/4 Eléctricos K Horizontal desde la esquina superior derecha 9-1/2 9-1/2 9-1/2 9-1/2 Todas las dimensiones son expresadas en pulgadas. 31-11087-1 05-17 GEA...

Este manual también es adecuado para:

Zet1sZet9050Zet2pZet2sZet9550Zek7000 ... Mostrar todo

Tabla de contenido