AVS Electronics OUTSPIDER PA Manual De Instrucciones página 46

Ocultar thumbs Ver también para OUTSPIDER PA:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Battery OUTSPIDER PA WS(UB) e OUTSPIDER DT WS(UB)
NOTE: OUTSPIDER PA WS(UB) and OUTSPIDER DT
WS(UB) are provided with a lithium 3.6V 8.5Ah battery
(mod. C Size) complete with cable with Amp. connector
end.
To power the s ensor, plug the battery Amp onto the
appropriate reference on the bottom of the sensor as
shown in the picture, and place the battery on the back of
the board.
Note:The "U" versions are supplied without a battery.
Terminal and Jumper OUTSPIDER PA WS(UB)(B) e OUTSPIDER DT WS(UB)(B)
T
T
Terminal
S1
E
1
N
1
S2
G
2
1
S3
3
4
5
6
7
Antimask
8
1
S4
T
T
3
2
1
1
S2
3
2
1
S1
1
S3
J u m p e r
P o s it io n
C lo s e d
S 1
O p e n
S 2
S 3
3
2
1
S 4
1
S4
B y d e f a u lt , ju m p e r S 2 , S 3 a n d S 4 a r e in p o s it io n s 1 - 2
BATTERY
ATTACHMENT
COMPARTMENT
Terminal block present on OUTSPIDER PA WS(UB)(U) and
OUTSPIDER DT WS(UB)(U) only
Description
It is possible to apply a positive between 3.0 and 3.6 V to
terminal " + " to give power to OUTSPIDER the WS (if
the model without battery " U " is used)
"+"
or
positive
You can use it as power output for an external transmitter
(if the model used is the "UB "with battery)
Note: In all cases, the detector performs a check on the
battery level
"-"
Negative Negative supply terminal
C-NC/NO terminal (see S4) for opening and strapping
Tamper
information (TT terminal)
Alarm
C-NC/NO contact relay (see S3) for alarm Indication
C-NC/NO contact relay (see S2) dedicated to the indication
of anti-masking and / or low battery according to the
Battery
setting of DIP 4 and 7 on SW2. Turns impulsively, after an
alarm indication.
T T : Normally closed input for connection of wall removal
tamper switch of the bracket. When open, causes a cyclical
TAMPER transmission each minute inhibiting the alarm
transmission, in the same way as when the tamper switch
of the front cover is open.
D e s c r ip t io n
T T i n p u t a c ti v e
T T i n p u t i n a c ti v e
1 - 2
A n ti m a s k r e la y w i th c o n ta c t C / N C a t r e s t
2 - 3
A n ti m a s k r e la y w i th c o n ta c t C / N O a t r e s t
1 - 2
A la r m r e la y c o n ta c t w i th C / N C a t r e s t
2 - 3
A la r m r e la y c o n ta c t w i th C / N O a t r e s t
1 - 2
Ta m p e r r e la y c o n ta c t w i th C / N C a t r e s t
2 - 3
Ta m p e r r e la y c o n ta c t w i th C / N O a t r e s t
Dip Switch OUTSPIDER PA WS e OUTSPIDER DT WS
DIP SWITCH SW 1:
Addressing sensors: Follow the radio sensors acquisition procedure described in
DIP 1 - 5
either the central stations or receiver which the sensors will be coupled with.
(Default: all ON = Sensor 1)
BATTERY
DIP 6
USB Enabled - Survival not active
DIP 7
Buzzer Enabled (Default)
DIP 8
Led Red Enabled (Default)
DIP SWITCH SW 2:
ON
DIP 1
OFF
DIP 2 OFF DEFAULT
DIP 3 OFF
ON
DIP 2
LOW
OFF
DIP 3
DIP 2 OFF
MEDIUM
DIP 3 ON
DIP 2 ON
HIGH
DIP 3 ON
OFF Only mod.UB and U
DIP 4
ON
DIP 6
NOT USED
DIP 7 OFF
ON
OFF
DIP 5
ON
OFF LOW CONSUMPTION
DIP 8
ON NORMAL CONSUMPTION detects and transmits the alarm without inhibition time (Default)
- 46 -
FUNCTIONS
ON
USB Disabled (Default)
Buzzer Disabled
Led Red Disabled
the sensor works based on the settings made by DIP 2,3 and 7
of strip SW 2 is not considering any changes made by PC
the sensor works based on the settings made by PC is not
considering any changes made by DIP 2,3 and 7 of strip SW 2
INFRARED SECTION CONFIGURATION
In this configuration, the infrared section has a default sensitivity
(studied for standard use) and executes a digital analysis of the
signals.
in this configuration, the infrared section has a low sensitivity
compared to the default and executes a digital analysis of the
signals which is more severe than the default one and considers
a dual impulse.
in this configuration, the infrared section has a medium sensitivity
compared to the default and executes a digital analysis of the
signals which is more severe than the default one.
in this configurations, the sensor has a high sensitivity and detects
any signal analysing amplitude and frequency.
battery control off
enables battery control
The battery low signal will be associated to putput no. 7
ANTIMASK
ANTIMASK disabled
ANTIMASK enabled (Default)
The antimask signal will be associated to putput no. 7
OPERATION
follows the DIP8 settings
and DIP8=OFF
the sensor inhibition time after transmitting an alari is set at 3
minutes
after an alarm transmission, the detector continues to analyze the
surrounding space but won't emit any more, at least for the
following 3 min during which it detects nothing.
OFF
(Default)

Publicidad

Tabla de contenido
loading

Tabla de contenido