Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
16 • ENGLISH
f For continuous operation, press the lock-on button
(2)
and release the variable speed switch. This option
is available only at full speed in both forward and
reverse modes.
f To switch the tllo off, release the variable speed
switch. To switch the tool off when in continuous
operation, press the variable speed switch again
and release it.
f Based on the different applications, turn around
the speed dial (11) to control the maximum speed.
Drilling in metal
Start drilling with slow speed and increase to full power while
applying firm pressure on the tool. A smooth even flow of
metal chips indicates the drilling metals. The exceptions are
cast iron and brass which should be drilled dry.
Note: Large [5/16" (8 mm) to 1/2" (13 mm)] holes in steel
can be made easier if a pilot hole [5/32" (4 mm) to 3/16"
(5 mm)] is drilled first.
Drilling in wood
Start drilling with slow speed and increase to full power
while applying firm pressure on the tool. Holes in wood
can be made with the same twist drills used for metal.
These bits may overheat unless pulled out frequently to
clear chips from the flutes. Work that is apt to splinter
should be backed up with a block of wood.
Drilling in masonry
When drilling in masonry, use carbide-tipped bits rated for
Impact drilling and be certain that the bits are sharp. Use a
constant and firm force on the tool to drill most effectively.
A smooth, even flow of dust indicates the proper drilling rate.
Screwdriving
f Select forward or reverse rotation.
Impact drilling (Fig. A)
f Select the Impact mode.
(1).
f Press the switch
Rotary drilling (Fig. A)
f Select the rotary drilling mode.
f Proceed as described for Impact drilling.
MAINTENANCE
Your Stanley power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Warning! Before performing any maintenance work on
the cord / cordless electric tools, the following points must
be implemented:
f Switch off the power of the equipment / tools and pull
off the plug;
f If the equipment / tools are equipped with independent
battery pack, please turn off the power and remove
the battery pack from the equipment / tools.
f If the equipment / tools are equipped with an integrated
battery, please run out the battery, before turning off
its power.
f Before the cleaning, unplug the charger plug from the
power source. In addition, except the regular cleaning
on your charger, no other maintenance is needed.
f Regularly use the soft brush or dry cloth to clean the
ventilation slot of the equipment / tools / charger.
f Regularly use a damp cloth to clean the motor
housing. Please do not use any abrasive cleaning
agents or solvent-based cleansing agents.
f Regularly open the clamping chuck and tap it gently to
remove any internal dust (after installation).
IMPORTANT
To unsure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (other than those listed in
this manual) should be performed by authorized service
centers or other qualified organizations, always-using
identical replacement parts. Unit contains no user
serviceable parts inside.
CLEANING
Warning! Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
Warning! Never use solvents or other harsh chemicals
for cleaning the nonmetallic parts of the tool. These
chemicals may weaken the material of the parts. Use
only mild soap and damp cloth to clean the tool. Never let
any liquid get inside the tool; never immerse any part of the
tool into liquid.
ACCESSORIES
The performance of your tool depends on the accessory
used. STANLEY accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you
will get the very best from your tool.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY
product needs replacement, or if it is of no further
use to you, do not dispose of it with household
waste. Make this product available for separate
collection.
Publicidad
Tabla de contenido
