Klippan KISS 2 Plus Manual De Instrucciones página 20

PREPARATIONS FOR FITTING
1. Remove the seat itself from the base by pulling the handle (by the arrow) outwards.
2. Adjustment of internal belt height. Pull out the internal belt to their fullest extent. Release the shoulder belt
tension from the back of the seat. Pull them out first, and then move them to their new height. Reattach them
properly in the tensioner.
NB: Make sure that they have not twisted together. If the internal belt is too short for the child, release the belt
loop in front of the seat from the plastic shell.
3. The seat is supplied with a comfort insert for new-borns. This insert consists of a seat and a back section. The
seat section can be used approx. up to 3 months and the back section to approx. 9 months of age.
4. When using the seat for children less than 9 kg, the soft base cap (A) shall be used. If the child's weight is over
9kg, the headrest (B) must be fitted on the base
HEADREST FOR CHILDREN OVER 9 KG
5. Child under 9kg shall travel with the seat in angle position 1
6. Headrest, for child over 9kg, is fitted on the base so that the left heel is first pushed down (A)...
7. ... Push out the right side (B) and push down the heels in the tracks. Bend carefully with a screwdriver if it is too
tight.
8. ... Push down the right side (D) so that the heels grips. End the mounting by pushing out the left side (E) and
down (F) then the heels goes in right position. (By bending out the heels with a screwdriver you can remove the
headrest from the base).
USE OF KISS 2 PLUS
9. Position of the child into the seat.
Push the button (A) to pull out the child seat´s own belts. Pull the shoulder belts as far as possible (B). Push the red
button (C) on the buckle to open the belt, then put them to each side (D) Fold the crotch strap forwards (E) with
the buckle and its safety sleeve. Place the child in the seat (F) with the crotch strap between the child´s legs. Push
the straps locking clasps (G) together as shown in the illustration, then click them into the buckle (H) . If required,
adjust the height of the belt at the back (as shown in illustration 2) Finally, tension the child seat´s belt by pulling
the strap (I) on the front of the seat, what is known as the one –handed tensioner.
NB. If the belt is too short, release the loop (in the end of strap I) from the plastic shell.
FITTING USING ISOFIX MOUNTS
10. Fold down the supporting leg before placing the base in the car. If you fit the Kiss on the front seat in your car.
The backrest of the car seat must be in upright position.
11. Place the base in the required location in the car. When fitting the seat in the rear, the seat in front of it may
need to be moved forwards slightly.
12. The instruction manual for your car will tell you where to find the ISOFIX mounts in your car. Lift up the red
catch (A) and move the base forward (B), so that the yellow arrows point are at one another (C).
13. Push the base on the ISOFIX MOUNTS. If you find it difficult to get at the mounts, use the ISOFIX guides included
( black plastic parts inserted around the ISOFIX mounts) for easier access.
14 Make sure that the indicator is green on both sides. This ensures that the base is locked properly.
15. Push the base onto the car seats backrest so that the base locks (click) properly. The black frame must be tight
to the car seat backrest.
16. Adjust the height of the supporting leg by pulling out the red button. Make sure that it sits firmly on the floor.
The supporting leg must be adjusted so that the base rests on the seat. Move on to fitting of the seat itself
REMOVAL FROM ISOFIX MOUNTS
17. NB: Removal Remove the supporting leg from the floor in order to facilitate removal of the base. Push down
the red catch and release the pretension from the base.
18. NB: Removal Lift the ISOFIX button on both sides and pull in the direction of the arrow so that the indicator is
red.
20