Technical Data; Impact Wrench - Chicago Pneumatic CP74 Serie Manual Del Usuario

Ocultar thumbs

Contenido

página de 37

/ 37
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

English (English)

1.Technical Data

Torque

Drive

Working

Model

[ft.lbs]

[inch]

[Nm]

max. pressure 6.3bar(90psi)

: Vibration level, k Uncertainty ; L

Declaration of noise and vibration statement (ISO 15744 and ISO 28927-2)

These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with the declared values of other

tools tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured in individual work places

may be higher. The actual exposure values and risk of harm experienced by an individual user are unique and depend upon the way the user works, the workpiece and the

workstation design, as well upon the exposure time and the physical condition of the user. We, CHICAGO PNEUMATIC TOOLS , cannot be held liable for the consequences

of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. This

tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at www. pneurop.eu/uploads/

documents/pdf/PN3-02-NV_Declaration_info_sheet_0111.pdf. We recommend a programme of health surveillance to detect early symptoms which may relate to noise or

vibration exposure, so that management procedures can be modified to help prevent future impairment.

2. Machine type(s)

• This product is designed for installing and removing threaded fasteners in wood, metal and plastic. No other use permitted. For professional use only.

• Please read the instructions carefully before starting the machine.

3. Mounting instruction

• Connect device as shown in Fig. 01 to a clean and dry air supply.

• Fix the accessories properly to the tool.

• To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.

Use the reverse switch (B) only when the drive spindle comes to a complete stop. Changing the speed before the drive spindle stops may damage the

machine.

• To switch rotation, push the switch (B) as shown in Fig. 02

• To adjust output power, turn the regulator (C) as shown in Fig. 03.

4. Lubrication

Motor

• Use an air line lubricator with SAE #10 oil, adjusted to two drops per

minute. If an air line lubricator cannot be used, add air motor oil to the inlet

once a day.

Recommended lubricant : CP Oil Protecto-lube

- 4 oz (0.12l) P/N: CA149661 (Air Tool oil)

- 20.8 oz (0.591l) P/N: CA000046 (Air Tool oil)

- 1gal (3.8l) P/N: P089507 (Airoilene oil)

5. Maintenance instruction

• Follow local country environmental regulations for safe handling and disposal of all components.

• Maintenance and repair work must be carried out by qualified personnel using only original spare parts. Contact the manufacturer or your nearest authorised

dealer for advice on technical service or if you require spare parts.

• Always ensure that the machine is disconnected from energy source to avoid accidental operation.

• High wear parts are underlined in the parts list.

• To keep downtime to a minimum, the following service kits are recommended :

Tune-up kit : see part list

6. Disposal

• The disposal of this equipment must follow the legislation of the respective country.

• All damaged, badly worn or improperly functioning devices MUST BE TAKEN OUT OF OPERATION.

• Repair only by technical maintenance staff.

7. EC Declaration of conformity

CHICAGO PNEUMATIC Tool Co. LCC - 1800 Overview Drive Rock Hill, SC 29730 - USA

We :

impact wrench

Machine type(s) :

CP749 & CP749-2

Declare that the product(s) :

Japan

Origin of the product :

is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to "Machinery"

applicable harmonised standard(s) :

Pascal Roussy (R&D Manager)

Name and position of issuer :

Saint-Herblain, 28/10/2015

Place & Date :

Technical file available from EU headquarter. Pascal Roussy R&D manager CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France

numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.

Original Instructions

Speed

Weight

Max

[ft.lbs]

[lb]

[min-1]

[Nm]

[kg]

Sound pressure dB(A), K

Serial Number : 000001 - 99999

EN ISO 11148-6:2012