Service, Maintenance And Repairs; Installation; Extraction Arm - PLYMOVENT MobilePro Manual De Instalación Y De Uso

Service, maintenance and repairs

- Obey the maintenance intervals given in this manual.
Overdue maintenance can lead to high costs for repair and
revisions and can render the guarantee null and void.
- Always use Personal Protective Equipment (PPE) to avoid
injury. This also applies for persons who enter the work area.
- Make sure the room is sufficiently ventilated.
- Use tools, materials, lubricants and service techniques which
have been approved by the manufacturer. Never use worn
tools and do not leave any tools in or on the product.
- Clean the area afterwards.
aTTENTION
Service, maintenance and repairs must be
performed in accordance with directive TRGS 560
and TRGS 528 by authorised, qualified and trained
persons (skilled) using appropriate work practices.
aTTENTION
Before you carry out service, maintenance and/or
repair jobs:
- fully disconnect the unit from the mains
- disconnect the compressed air supply
Personal protective equipment (PPE)
Wear respiratory protection and protective
gloves during service, maintenance and
repairs.
WaRNINg
The industrial vacuum cleaner that you use during
service and maintenance must meet dust class H
according to EN 60335-2-69 or HEPA class
(efficiency ≥99.97% at 0.3 µm).
4

INSTaLLaTION

4.1 Tools and requirements
You need the following tools and requirements to install the
unit:
- basic tools
4.1.1 To be sourced locally
For connection to the local mains (50 Hz types only):
- a suitable plug
For connection of the compressed air hose:
- compressed air fitting G 3/8" (male)
In case of working light HL-20/24-160 (option):
- adhesive cable tie mounts and cable ties or equivalent
4.2 Unpacking
Make sure that the product is complete. The package contains:
- mobile filter unit
- hexagon bolt M6x25 (8) + washer (8) for connection of the

extraction arm

- cable gland (2) for connection of the optional working light
HL-20/24-160
Refer to Fig. III on page 69 for instructions to
take the unit from the pallet.
aTTENTION!
Do not use a fork-lift truck to lift the unit. It will
damage the dust tray.
4.3 Extraction arm
To operate the MobilePro you must install one of the following
extraction arms:
- KUA-2/S / KUA-3/S / KUA-4/S (ball bearing extraction arm)
- EA-3/S / EA-4/S (hose tube extraction arm)
0000104750/210616/B MobilePro | MobilePro/PTFE
To install the extraction arm, proceed as follows.
Fig. 4.1
• Install the rotating flange (H) on the filter housing with the
8 bolts M6x25 + washers.
• Move the hose clamp (D) and the rubber collar (E) over the
hinge rod (B).
• Put the swivel ring (F) over the hinge rod (B)
• Put the washer (G) over the hinge rod.
aTTENTION!
Make sure to install the washer between the
rotating flange and the swivel ring to avoid damage.
• Put the hinge rod (B) in the rotating flange (H) and attach
it with the locking pin (C). Tighten it with a hex key.
• Put the hose (A) over the swivel ring (F).
• Tighten the hose with the hose clamp (D).
• Put the rubber collar (E) over the connection between the
swivel ring (F) and the rotating flange (H) to make it
airtight.
A
B
C
Fig. 4.1 Mounting of the extraction arm
To assemble and adjust the extraction arm itself,
refer to the corresponding manual.
4.3.1 Option: working light HL-20/24-160
Fig. 4.2
• Install the working light in the hood of the extraction arm
in accordance with the instruction sheet.
• Attach the cable (A) to the tubes of the arm and to the
unit, e.g. with adhesive cable tie mounts and cable ties.
Make sure that the cable is long enough:
- when the extraction arm is in fully folded position;
and
- to rotate the extraction arm (max. 359°)
4. The dashed line indicates the end position.
.
4
D
E
F
G
H
A
D
F
E
H
EN - 6