Troubleshooting; Spare Parts - PLYMOVENT MobilePro Manual De Instalación Y De Uso

6.3.1 Filter washing
To extend the lifespan of the filter cartridge, you can wash it a
number of times before you finally have to replace it
Personal protective equipment (PPE)
Wear respiratory protection and protective
gloves when you wash the filter cartridge.
aTTENTION
- Handle the filter cartridge with care.
- Make sure that the filter cartridge is not damaged.
To wash the filter cartridge, proceed as follows.
• Disassemble the filter cartridge as described in section 6.3.
• Soak it in water with EFC detergent at max. 60°C (140°F).
• Hose it clean.
• Let it dry thoroughly.
aTTENTION
No steam cleaning.
7

TROUBLEShOOTINg

If the unit does not function (correctly), consult the checklist
below to see if you can remedy the error yourself. Should this
not be possible, contact your supplier.
WaRNINg
Obey the safety regulations that are written in
chapter 3 when you carry out the activities below.
Symptom Problem
ALARM light No filter
is on cleaning
The ALARM -
light remains
on after
manual filter
Extraction
cleaning
capacity
insufficient
The fan does The unit does
not start not function
11. You must replace the filter cartridge immediately when it is damaged or when
the ALARM light remains on during use, which indicates that the filter cartridge
is clogged.
0000104750/210616/B MobilePro | MobilePro/PTFE
.
11
Possible Solution
cause
No compressed Connect or repair
air available or the compressed air
air pressure too supply.
low Subsequently:
- push the MANUAL
CLEANING button
(hold for 5
seconds)
- push the START/
STOP button two
times to reset the
ALARM light
Clogged filter Replace the filter
cartridge cartridge
No reset Push the START/
STOP button 2
times (off and on)
Clogged filter Replace the filter
cartridge cartridge
No mains Connect the mains
voltage voltage
The mains cord Repair or replace
is defective the mains cord
Loose contacts Repair the contacts
Motor defective Repair or replace
the motor
START/STOP Replace the green
button (green) button
is defective
Thermal relay is Reset the thermal
activated relay
Symptom Problem
The fan does The unit does
not start not function
(cont.)
The fan Extraction
makes a capacity
humming insufficient or
sound, but no extraction
does not run at all
Poor The unit does
extraction not function
capacity properly
Pollution of
the facility
No filter
cleaning
Hissing sound No filter
cleaning
MANUAL No manual
CLEANING activation of
button does the filter
not react. cleaning
system
8

SPaRE PaRTS

The following spare parts are available for the product (refer to
exploded view Fig. V on page 71).
article no. Description
general
0000101364 Wheel cover grey (2 pieces)
0000101409 Fuse 3.15A 5x20 mm UL
0000101413 Transformer 120-575V 24V 75VA
0000101751 CART-O / Filter cartridge
0000101752 CART-OA / Filter cartridge
0000102220 Pressure switch 800 Pa
0000102411 Drain valve ½ inch
0000102584 Lock kit for CART filter cartridge
0000102598 Star knob M12
0000102762 Cover plate for filter cartridge
0000104768 Indicator light red
0000104961 PC board MobilePro, incl. software
0000110155 CART-O/PTFE / Filter cartridge
0040900010 Magnetic valve AC
0040900120 Push button black
0040900130 Push button green incl. LED
0805030010 Wheel Ø 250 mm black (excl. wheel cover)
0805040010 Swivel castor Ø 125 mm with brake
Possible Solution
cause
Thermal relay is Replace the thermal
defective relay
Motor uses 2 Repair the phase
phases instead connection
of 3 (3-phase
motor only)
Inverted Change the
direction of direction of rotation
rotation of the
motor (3-phase
motor only)
Clogged filter Replace the filter
cartridge cartridge
Filter cartridge Replace the filter
ripped or cartridge or place it
placed correctly
incorrectly
Loose Repair the
compressed air compressed air
connection connection
No compressed Connect or repair
air available or the compressed air
air pressure too supply
low
Membrane Replace the
valve defective membrane valve
or worn
Membrane Replace the
valve defective membrane valve
or worn
The button is Push and hold the
not held long button for 5
enough. seconds.
MANUAL Replace the black
CLEANING button.
button (black)
is defective.
[MobilePro only]
12
[MobilePro only]
12
[MobilePro/PTFE only]
12
EN - 10