InSinkErator F-HC3300C Manual De Instalación página 2

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
I For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this
steaming hot water tap.
I Make sure that all electrical wiring and connections conform to local codes.
I A standard, earth (grounded) electrical outlet is required under the sink for the tap's electrical power.
I The wall outlet powering your tap must have electrical power supplied to it continuously.
I This outlet must be fused and should not be controlled by the same wall switch that operates the food waste
disposer. Fuse/circuit breaker required is 10 amp for 230 volt (10 amp for 220-240 volt UK) and 15 amp for
120 volt.
I To ensure proper operation, this unit is not intended to be flushed with chlorine. If you suspect elevated levels
of chlorine in your water, it is recommended to use our water filtration system.
I In Australia, all plumbing and electrical work must be completed by a qualified tradesperson.
I To prevent damage or unit not operating properly, the water pressure must be between 172 kPa - 862 kPa
(1.7 bar - 8.6 bar; 25 psi - 125 psi). Ambient (room) temperature between 10ºC and 38ºC. In Australia, an
Australian water mark approved 350 kPa set pressure limiting valve and dual check valve must be used.
I Moving parts inside the tank causing a rattling noise is normal.
I If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
ADDITIONAL CONSIDERATIONS
In Australia and New Zealand, the installation must conform to AS3500.4.1 or AS/NZS 3500.4.2 (Clause 9.b).
Important: Always arrange the power cord so that it cannot come in contact with hot surfaces.
I Use this water heater only for its intended use as described in this manual.
I This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of appliance by a person responsible for their safety. Children should be supervised to ensure
that they do not play with hot water tap. To reduce the risk of injury, close supervision is required when an
appliance is used near children.
I Do not operate this product if it has been or appears to be damaged in any manner or after the product
malfunctions, or is dropped. Return the complete product immediately to your retail dealer for inspection, and
if necessary, adjustment or repair.
Electric Shock Hazard: To reduce the risk of electric shock, do not immerse or expose
the product, flexible cord or plug to rain, moisture or any liquid or when standing in
or on damp or wet surfaces. If any electrical product falls into water, UNPLUG it
immediately. DO NOT REACH INTO THE WATER. Important: Prior to reconnecting to
the power supply, the product should be inspected by a qualified technician.
I Do not disconnect the product from the power supply by pulling on the cord.
I Do not use the product for other than its intended use as described in these instructions. The use of accessory
attachments other than those recommended by the manufacturer may cause safety hazards.
I The recommended connection may be made to an existing cold water line with a branch terminating with a
shutoff valve, a pressure relief and dual check non-return valve sited adjacent to the product.
Property Damage: The flexible vent and outlet tubes must be correctly
connected to the tap supplied by the manufacturer. They must not be obstructed
or connected to a normal type tap or any other type. Important: Do not allow the
unit to continuously boil.
I The filter is attached to cold water only.
I Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
I The filter is made in the USA.
2
WHAT YOU NEED TO GET STARTED
Equipment Required:
I Drill
I Compression fitting, T-fitting
or saddle valve
I Adjustable spanner
Equipment You May Need:
I Anchors for plasterboard
Hole saw
I
If you intend to use the sprayer hole in the sink for the hot water tap, you may need a 3.18mm plug or a 6.35mm
cap (not supplied) for the sink spray hose line. See Step 1B. If you need to cut a mounting hole in the stainless
steel sink, you may need a hole punch or a 35mm - 38mm hole saw made for cutting stainless steel.
What if you don't have a sprayer hole or don't want to use it?
Many householders replace the soap dispenser in their sink with a steaming hot water tap. If drilling a hole into a
stainless steel sink or worktop, you can cut a mounting hole for the tap with a hole saw for stainless steel, or you
can use a hole punch.
Hole size requirements: – HC1100, HC3300 and H3300, a 35mm - 38mm hole is required.
– GN1100, hole requirement is 32mm - 38mm.
Consult a professional before drilling into a surface other than stainless steel.
IN THIS PACKAGE
HC3300-1, -3
H3300-1, -3,
Semicircular
Mounting Plate
HC1100-1, -3
Rubber O-Ring
GN1100-1, -3
9.5mm White Tubes (2)
SWT-3
Filter Head & Cartridge
SWT-FLTR-1, -3
(SWT-FLTR only)
I Phillips and flat blade screwdrivers
I Pencil
I Tape Measure
Spirit level
I
I Basin nut wrench
Hole punch
I
Brass Seat
(HC3300, H3300)
Hex Nut
19mm Screws (4) Back Flow Protection Valve
(Australia/New Zealand only)
Plug (1)
Y-Quick Connector John Guest Fitting
(Australia only)
Hex Tool