Bestway MY FIRST FRAME POOLS Manual Del Usario página 4

CHOOSE THE CORRECT LOCATION
IMPORTANT:
The pool must be set up on a completely flat and level surface. Please do not install the
pool if the surface is Inclined or sloped.
Correct conditions to set up the pool:
• The selected location has to be capable of uniformly supporting the weight for the entire time the pool is installed,
moreover the location must be flat and must be cleared of all objects and debris including stones and twigs.
• We recommend positioning the pool away from any objects kids could use to climb into the pool.
NOTE:
Position the pool near an adequate drainage system to deal with overflow or to discharge the pool.
Incorrect conditions to set up the pool:
• On uneven ground the pool may collapse causing serious personal injury and/or damage to personal property and will
void the warranty and prevent any service claims.
• Sand should not be used to create a level base; the ground must be dug out if necessary.
• Directly under overhead power lines or trees. Be sure the location does not contain underground utility pipes, lines or
cables of any kind.
• Do not set up the pool on driveways, decks, platforms, gravel or asphalt surfaces. The selected location should be firm
enough to withstand the pressure of the water; mud, sand, soft / loose soil or tar are not suitable.
• Grass or other vegetation under the pool will die and may cause odors and slime to develop, therefore we recommend
removing all grass from the selected pool location.
• Avoid areas prone to aggressive plant and weed species that may grow through the ground cloth or liner.
NOTE:
Check with your local city council for by-laws relating to fencing, barriers, lighting and safety
requirements and ensure you comply with all laws.
NOTE:
If have a filter pump, refer to the pump's manual for instructions.
NOTE:
The ladder must match the pool size and should to be used only for entering and exiting the pool. It is
forbidden to exceed the permitted payload of the ladder. Check regularly if the ladder is properly assembled.
Installation
Fig. 1 Fig. 2
Fig. 4 Fig. 5
I
Fig. 7 Fig. 8
E
Assembly of the Frame pool can be completed without tools.
NOTE:
It is important to assemble pool in the order shown below. Install your pools according to the above
illustrations.
1. Lay out all parts and check that you have the correct quantities as listed in the parts guide. If you are missing
any part do not assemble the pool, contact our Customer Service Department for assistance.
NOTE:
Vertical pool legs are packaged inside the top rails.
2. If pool was purchased with a ground cloth, spread carefully at the desired location. This pool may have been
purchased with a Bestway Filter Pump, if a pump is to be used (recommended and also available separately)
the pool should be located within distance of a power outlet.
3. Place the Leg Bands (L) on the ground (See Fig. 1). There are different lengths of Leg bands (L), please ensure
you have used the correct sizes at the correct locations.
4. Spread out the pool and put it on the Leg Bands (L). Make sure it is right side up (See Fig. 2). Let it sit exposed
to direct sunlight for 1 hour or more so the pool is more flexible during set up.
5. Turn the pool so the drain valve is near the area where your plan to drain the water and pump valves are facing
the outlet for the optional filter pump.
ATTENTION:
Do not drag the pool on the ground in order to avoid damaging the linear on sharp
objects. Bestway Inflatables will not be responsible for damage caused to the pool due to mishandling or failure to
follow these instructions.
6. Insert all of the top rails into the pole sleeves on the top of the pool (See Fig. 3). The combinations for top rails
are different for different sizes pools, see the Structure Section for detail.
7. At the middle opening of each sleeve, insert the two ends of the top rails into the Connector (I).(See Fig. 4)
NOTE:
At each Connector ensure both top rails are properly inserted.
8. At the corners, insert the top rails into the Corner Seats (J). Insert the Connection Pins (K) into the pre-drilled
holes locking the top rails into position.(See Fig. 5)
9. Insert the Vertical Pool Legs (F) into the bottom of the Corner Seats (J). (See Fig. 5)
10. On the sides of the rectangle, insert the T Support (E), Vertical Pool Legs (F) or the Y-Vertical Pool Legs (G,H)
into the vertical holes of the Connectors (I). (See Fig. 6, See Fig. 8)
11. Connect the Side Support Legs (H) to the Y-Vertical Pool Legs (G). Ensure the spring-loaded pins lock into the
pre-drilled holes. (See Fig. 6)
12. On each corresponding Pool Leg located on the sides of the rectangle, put the Pool Legs (E, F or G) through
the loops of the Leg Bands (L). This will keep both corresponding pool legs locked in position.
(See Fig. 6, See Fig. 8)
13. Attach all Footings (M&N) to the bottom of the Vertical Pool Legs (F) and the Side Support Legs (H).
(See Fig. 7)
14. Test the Frame to ensure all connections are secure before filling with water.
15. Insert the blue stopper plug into the inlet and outlet on the inside wall of the pool.
16. Ensure drain valve is firmly closed.
17. Put 1in to 2in water in the pool to cover the floor. Once pool floor is slightly covered, gently smooth out all
wrinkles. Start in the center of the pool and work your way clockwise to the outside.
S-S-003662/21.0x28.5cm(儿童支架水池 C版) JS-YF-2015-B-04775/英
Fig. 3
Fig. 6
F/G
L
J
K
G
F
E/F/G
L
FILLING POOL WITH WATER
ATTENTION:
Do not leave pool unattended while filling with water
1. Fill pool to drain valve.
STOP
2. Turn water off. Check that the water is not collecting on any side to ensure the pool is level. If pool is not
level, drain water and re-level ground by digging out (See Fig. 10). Never attempt to move the pool with
water in it, serious personal injury or damage to the pool may result.
NOTE:
Your pool may contain a great deal of pressure. If your pool has any bulge or uneven side then the
pool is not level, the sides may burst and the water may discharge suddenly causing serious personal injury and/or
damage to property.
3. If level,fill pool to lowest pump valve.
STOP
4. Turn water off. Check valves for secure fit.
5. Fill pool until water capacity is 90% (See Fig. 9), DO NOT OVERFILL as
this could cause the pool to collapse. In times of heavy rainfall you may
need to empty some of the water to ensure the level is correct.
6. Check pool for any leaks at valves or seams, check ground cloth for any
evident water loss. Do not add chemicals until this has been done.
7. In the event of a leak, patch your pool using the patch kit provided. Refer to the FAQ's for further information.
Fig. 9 Fig. 10
Proper Water Level
NOTE:
Drawings for illustration purpose only. May not reflect actual product. Not to scale.
ATTENTION:
Do not use pump when pool is in use.
During the season of use of the swimming pool, the filtration system must be necessarily put into service every day,
enough for a long time to assure at least a complete renewal of the volume of water.
Pool Maintenance
If you do not adhere to the maintenance guidelines below, your health might be at risk, especially that of your children.
IMPORTANT:
If you don't respect the ideal values of the water chemicals the PVC can be damaged and
become discolor.
The following table lists the sequence of the tests that should be carried out for the ideal values and possible actions.
Regularly check the pH value and chlorine concentration weekly and adjust to the ideal values.
H
TEST IDEAL VALUES
pH value 7.4– 7.6
Cyanuric acid 30 – 50 ppm
Free chlorine 2 – 4 ppm
Chlorine compound 0
Algae None visible
Calcium hardness 200 – 400 ppm
To keep your pool clean:
1. Contact your local pool supply shop for advice and purchase of chemicals and pH kits. One of the most important
factors to increase the life of the liner is to keep continously clean and healthy water.
Please strictly follow the instructions from professional technicians for the water treatment through the use of
chemicals.
2. Locate a bucket of water next to pool to clean users' feet before entering pool.
3. Cover the pool when not in use.
4. Skim pool regularly to avoid settled dirt.
5. Check and wash the filter cartridge regularly.
6. Gently clean any scum from below the top ring with a clean cloth.
7. Please be careful in case of rain water, kindly check that the water level is not higher than the expected. If so, YOU
HAVE TO DISCHARGE THE EXCESS WATER.
Proper maintenance can maximize the life of your pool.
During the season of use of the swimming pool, the filtration system must be necessarily put into service every day,
enough time to assure at least a complete renewal of the volume of water.
Repair
Check pool for any leaks from valves or seams, check the ground cloth for any evident water loss. Do not add
chemicals until this has been done.
NOTE:
In the event of a leak, patch your pool using the Heavy-duty repair patch provided. Refer to the FAQs for
further information.
Dismantling
1. Unscrew the drain valve cap on the outside of the pool counter clockwise and remove.
2. Connect the adaptor to the hose and put the other end of the hose in the area where you are going to drain your
pool. (Check local regulations for drainage by-laws).
3. Screw control ring of the hose adaptor onto the drain valve clockwise. The drain valve will be open and water will
ATTENTION:
start to drain automatically.
4. When draining is finished, unscrew the control ring to close the valve.
5. Disconnect the hose.
6. Screw the cap back onto the drain valve.
7. Air dry pool.
ATTENTION:
Do not leave the drained pool outside.
Storage and Winterization
1. Please remove all the accessories and spare parts of the pool and store them clean and dry.
2. Once pool is completely dry, sprinkle with talcum powder to prevent pool from sticking together, fold pool carefully. If
pool is not completely dry, mold may result and will damage the pool liner.
3. Store liner and accessories in a dry place with a moderate temperature between 5ºC / 41ºF and 38ºC / 100ºF.
4. During the rainy season, pool and accessories should be stored as per above instructions also.
5. Improper draining of the pool might cause serious personal injury and/or damage to personal property.
6. We strongly recommend the pool is disassembled during the off season (winter months). Store in a dry location out
of children's reach.
4
Fig. 8
0°
Water flow can be controlled with the control ring.
S-S-003662