Symbols; Operating Instruction; Cleaning And Maintenence; Environment - MaxPro PROFESSIONAL MPCS1300 Manual Del Usuario

• If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left
unattended
ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS
Warning! The laser beam potentially causes severe eye damage. Never look or stare directly into the laser
beam.
During use, do not point the laser beam at people, directly or indirectly through reflecting surfaces.
This laser complies with class 2 according to EN 60825-1/A11, 1996. The unit includes no servicing
components. Do not open the housing for any reason. If the unit is damaged, have the damage repaired
by an authorized repair agent.

SYMBOLS

Read the manual
Warning
Double insulation
Wear eye protection

OPERATING INSTRUCTION

Changing the blade (Fig.1) (Fig.2)
Switch off the tool and unplug the power cord. Disconnect the sole and lower it to its lowest position. Lock
the blade with the spanner supplied. Undo the locking screw and the washer. Take off the blade. Install the
new blade by following these instructions in the reverse order.
Setting the cutting depth
(Fig.4)
Switch off the tool and unplug the power cord. Undo the depth adjustment screw. Adjust the sole to the
desired sawing depth and tighten the screw.
Setting the sawing angle (Fig.5)
Switch off the tool and unplug the power cord. The sawing angle can be set between 0°and 45°. Undo the
two screws holding the sole. Turn the sole to the required angle. Tighten the screws to lock the sole.
Parallel fence
The parallel fence is used to saw parallel with the edge of the workplace. Switch off the tool and unplug
the power cord. Place the fence in the grooves at the front edge if the sole. Set the desired sawing width
and tighten the screws to lock the parallel fence.
Laser line indication (Fig.6)
Laser line indication is used to make it easier to saw along the desired line.
IMPORTANT: Do not lock into the laser beam – risk of eye injury.
CLEANING AND MAINTANCE
Always pull out the mains power plug before starting any cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the
equipment with a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or
6
Wear ear protection
Wear dust mask
Do not dispose of old appliances in the
household garbage
Keep your hands and feet away from all
opening
GB
solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the
device.
Carbon brushes
In case of excessive sparking, have the carbon brushes checked only by a qualified electrician.
Important! The carbon brushes should not be replaced by anyone but a qualified electrician.
Maintenance
There are no parts inside the equipment which require additional maintenance.

ENVIRONMENT

Do not dispose of electric tools, accessories and packaging together with household waste material
- in observance of European Directive 2002/96/EC on waste of electric and electronic equipment and its
implementation in accordance with national law, electric tools that have reached the end of their life must
be collected separately and returned to an environmentally compatible recycling facility.

TROUBLE SHOOTING

Fault Symptom Possible Cause
Out of service Disconnection between plug and
power socket
shortcircuit in power supply
At switch-off
Loose switching contact
Burnout of stator or rotor coil
Stator wiring disconnection
Disconnection between carbon
brush and commutator
Sluggish start-up, falling short of Unsmooth running in mechanical
running speed part
Low supply voltage
Burnout of switch contact
Excessive sparkling during running Underpressure in carbon brush
spring
Excessive wearout of carbon brush Replace machinery parts by repairer
Ring fire caused by shortcircuit in
rotor winding shortcircuit
Ring fire caused by shortcircuit in
commutator segment
Overvoltage in supply power
Disconnection between carbon
brush and commutator
Excessive machinery noise Electric motor at fault
Gear wheel or rotor tooth
damaged
Failed to reach rated power Electrocircuit overload due to
lighting device, public utility or
other electric appliances
Machine superheating Electromotor overload
Insufficient motor cooling
Troubleshooting
Put plug in power socket
Repair and reconnection
Switch on
Replace switchboard by repairer
Replace stator or rotor by repairer
Reconnection by repairer
Replace carbon brush
Check mechanical part by repairer
Regulate supply voltage
Replace switchboard by repairer
Regulate supply voltage
Check or replace rotor by repairer
Regulate to high speed running
Regulate supply voltage
Replace carbon brush
Check motor by repairer
replace gear wheel or rotor
No use of public utility or other
electric appliances on machine-
connected electrocircuit
Overload protection
Dedust air outlet
GB 7