Publicidad
Idiomas disponibles
Idiomas disponibles
R. IEC POWER SOCKET - The line cord must be
connected to a grounded AC receptacle in accor-
dance with the voltage and frequency ratings as
specified on the rear panel of the unit.
S. FUSE - Replace a blown fuse only with a fuse of the
type and rating as specified on the rear panel of the
unit. If the amp repeatedly blows fuses, have the unit
tested by an authorized Fender service technician.
T. POWER - Switches the unit ON and OFF.
U. STANDBY - In standby mode, power is supplied only
to the tube filaments to keep them warm and ready
to operate. Use standby during short breaks to
eliminate warm-up time and extend the life of the
tubes.
V. MAIN SPEAKER JACK - This is the primary speaker
connection. Speakers (internal or external) must
always be connected here while operating the unit.
TYPE:
PART NUMBERS:
POWER REQUIREMENTS:
FUSE TYPE:
100V-120V models:
230-240V models:
IMPEDANCES
SPEAKER COMPLEMENT:
DIMENSIONS
WEIGHT:
w w
w
w w
w . . f f e
e n
n d
d e
PR 469
021-7600-000, 120V, 60Hz (USA),
021-7640-000, 230V, 50Hz (UK),
021-7670-000, 100V, 50-60Hz (Japan)
270W
3A, fast-blow, 125V minimum,
1. 6A, fast-blow, 250V minimum,
Inputs 1:
1M ohms (both channels)
Inputs 2:
136K ohms (both channels)
Output:
2 ohms
Four 10 in. (25.4 cm) vintage reissue, P/N 055613
Height:
24 7/8 in.
Width:
25 1/8 in.
Depth:
10 1/2 in.
65 lbs.
Product Specifications are subject to change without notice.
✧
e r
r . . c
c o
o m
m
w w
w
F F
e e
n n
d d
e e
r r
® ®
® ®
' '
6 6
5 5
S S
u u
p p
F F
e e
n n
d d
e e
r r
' '
6 6
5 5
S S
u u
p p
W. EXTERNAL SPEAKER JACK - Plug in external
speakers here. This jack is wired in parallel with the
main speaker jack.
*** NOTE: The amp is optimized for a 2 ohm speaker
load, which is the rating of the internal speaker
configuration. If a speaker load other than 2 ohms is
used, the amplifier will distort before reaching
maximum output, and the life of the tubes will be
reduced.
Two external 4 ohm speaker cabinets
would provide the recommended 2 ohm load.
X. FOOTSWITCH - Plug the included footswitch in here
to enable remote on/off switching of Reverb and
Vibrato.
*** NOTE: Vibrato will NOT work without the footswitch
connected, but the reverb effect will.
Y. REVERB OUTPUT / INPUT - RCA jack connections
for routing the reverb signal to and from the reverb
pan.
S S
p p
e e
S S
p p
e e
021-7660-000, 230V, 50Hz (Europe),
021-7630-000, 240V, 50Hz (Aust),
(63. 2 cm)
(63. 8 cm)
(26. 7 cm)
(24. 3 kg)
w w
w . . m
m r
r g
g e
e a
e e
r r
R R
e e
v v
e e
r r
b b
® ®
® ®
e e
r r
R R
e e
v v
e e
r r
b b
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
a r
r h
h e
e a
a d
d . . n
n e
7
e t
t
Publicidad
