Field Wiring Guidelines; Internal Wiring - Parts Table; Connection Of The Indoor Unit Power Supply And Communication Cable - Rotex RKHBH008BA Manual De Instalación

Item Description
1 Power supply cable for outdoor
unit
2 Indoor unit power supply and
communication cable
3 Power cable for bottom plate
heater
4 Power supply cable for backup
heater
5 Room thermostat cable
6 3-way valve control cable
7 2-way valve control cable
8 Booster heater power supply
and thermal protection cable
9 Thermistor cable
10 Booster heater power supply
cable
11 Benefit kWh rate power supply
cable (voltage free contact)
12 User interface cable
(a) Refer to nameplate on outdoor unit.
2
(b) Cable section 2.5 mm
(c) Minimum cable section 0.75 mm
(d) See table under "Connection of the backup heater power supply" on page 18.
(e) The thermistor and connection wire (12 m) are delivered with the domestic hot
water tank.
2
(f) Cable section 0.75 mm till 1.25 mm
Voltage free contact shall ensure the minimum applicable load of 15 V DC,
10 mA.
2
(g) Cable section 0.75 mm till 1.25 mm
CAUTION
Select all cables and wire sizes in accordance with
relevant local and national regulations.
WARNING
After finishing the electric work, confirm that each electric
part and terminal inside the electric parts box is connected
securely.

Internal wiring - Parts table

Refer to the internal wiring diagram supplied with the unit (on the
inside of the indoor unit switch box cover). The abbreviations used
are listed below.
A1P ................. Main PCB
A2P ................. Digital controller PCB (user interface)
A3P ......... * ..... Thermostat (RKRTW/R) (PC=internal Power Cicuit)
(optional)
A4P ......... * ..... Remote alarm address card (EKRP1HB) (optional)
A4P ......... * ..... Receiver PCB (RKRTR) (optional)
E1H ................. Backup heater element 1
E2H ................. Backup heater element 2
E3H ................. Backup heater element 3
E4H ......... # ..... Booster heater (3 kW)
F1B,F3B .......... Fuse backup heater
F2B.......... # ..... Fuse booster heater
F1T.................. Thermal fuse backup heater (250 V, 94°C)
FU1 ................. Fuse 3.15 A T 250 V for PCB
FU2 ................. Fuse 5 A T 250 V
FuR,FuS.......... Fuse 5 A 250 V for remote alarm PCB
K1M................. Contactor backup heater step 1
K2M................. Contactor backup heater step 2
K3M......... # ..... Contactor booster heater
K4M................. Pump relay
K5M,K6M ........ Contactor for backup heater all pole disconnection
M1P................. Pump
M2S....... ## ..... 2-way valve for cooling mode (field supply)
M3S......... # ..... 3-way valve: floor heating/domestic hot water
Installation manual
17
Required
number of Maximum
conductors running current
(a)
2+GND
(b)
3+GND
(c)
2
(d)
2+GND or
3+GND
(c)
3 or 4 100 mA
(c)
2+GND 100 mA
(c)
2+GND 100 mA
(b)
4+GND
(e)
2
2+GND 13 A
2 (f)
2 (g)
2
2
, maximum length: 50 m.
2
, maximum length: 500 m.
PHC1 ............... Optocoupler input circuit
Q1DI ................ Earth leakage circuit breaker (field supply)
Q1L.................. Thermal protector backup heater
Q2L,Q3L ..# ..... Thermal protector booster heater
R1H ......... * ..... Humidity sensor (RKRTR) (optional)
R1T.......... * ..... Ambient sensor (RKRTW) (optional)
R1T.................. Outlet water heat exchanger thermistor
R2T.......... * ..... External sensor (floor or ambient) (EKRTETS)
(optional)
R2T.................. Outlet water backup heater thermistor
R3T.................. Refrigerant liquid side thermistor
R4T.................. Inlet water thermistor
R5T..........# ..... Domestic hot water thermistor
S1L .................. Flow switch
S2S.................. Benefit kWh rate power supply contact
S3S.................. Dual set point 2 contact
S4S.................. Dual set point 1 contact
SS1.................. DIP switch
TR1.................. Transformer 24 V for PCB
V1S.................. Spark suppression 1
V2S.................. Spark suppression 2
X1M~X9M........ Terminal blocks
* Optional
# Applications with domestic hot water tank only
## Heating/cooling applications only

Field wiring guidelines

■
Most field wiring on the indoor unit side is to be made on the
terminal block inside the switch box. To gain access to the
terminal block, remove the indoor unit cover and switch box
service panel, see "Opening the indoor unit" on page 9.
WARNING
Switch off all power supply – i.e. outdoor unit power
supply and backup heater and domestic hot water
tank power supply (if applicable) – before removing
the switch box service panel.
■
Cable tie mountings are provided at the bottom of the switch
box. Fix all cables using cable ties (field supply).
■
A dedicated power circuit is required for the backup heater.
■
Installations equipped with a domestic hot water tank (optional),
require a dedicated power circuit for the booster heater.
Please refer to the domestic hot water tank installation manual.
Connection of the indoor unit power supply and
communication cable
Power circuit and cable requirements
Power supply for the indoor unit is to be provided through the outdoor
unit. Data communication with the outdoor unit is provided through
the same cable.
For all guidelines and specifications regarding field wiring between
the indoor unit and the outdoor unit, please refer to the outdoor unit
installation manual.
Procedure
1 Using the appropriate cable, connect the power circuit to the
appropriate terminals as shown on the wiring diagram and the
illustration below.
2 Connect the earth conductor (yellow/green) to the earthing
screw on the switch box mounting plate.
3 Fix the cable with cable ties to the cable tie mountings to ensure
strain relief.
4 When routing out cables, make sure that these do not obstruct
mounting of the indoor unit cover, see figure 3.
Indoor unit for air to water heat pump system
RKHBH/X008BA
4PW54224-1A