Publicidad
Idiomas disponibles
Idiomas disponibles
ELECTRONIC RPM REGULATION
LE71TE-LS71TE-LR71TE: The rpm can be adjusted by rotating the wheel
speed adjustment wheel (3) located on the rear of the tool. The choice of speed
depends on the characteristics of the abrasive paper disc and the material to be
worked.
DUST EXTRACTION
ATTENTION Hazardous dust can be produced during sanding
operations:
Always connect an adequate extraction device
In case of work producing dust, wear a mask
INTEGRATED EXTRACTION
- To guarantee optimal extraction of the powder empty the conical filter (8) in
time, accurately cleaning the filter holder (8a) and regularly cleaning the
cartridge (8b);
- During works on the vertical surfaces, position the machine so the conical filter
is turned downwards.
- Conical filter assembly: position the conical filter (8) on the extractor tube
coupling (4). Push the conical filter until it stops.
- Conical filter filling testing: the filling status of the conical filter is easily
controlled using the transparent filter holder (8.a).
- Conical filter cleaning: to empty the conical filter, remove it from the extractor
tube coupling working in the opposite direction to assembly;
- Release the cartridge (8.b) and release it from the filter holder;
- Empty the filter holder;
- Clean the cartridge plates with a soft brush.
EXTERNAL EXTRACTION
- During vertical surface works position the machine in such a way the extractor
tube is turned downwards.
- Assembly: insert an extractor tube on the coupling for the extractor tube (4);
- Connect the extractor tube to an adequate vacuum system (not supplied).
ACCESSORIES
LE71T-LE71TE Velcro sand paper 80x130 mm with holes for extraction.
LS71T-LS71TE Delta Velcro sand paper with holes for extraction.
LR71TE Velcro sand paper discs Ø 125 mm with holes for extraction.
10
MAINTENANCE
All maintenance operations are carried out with the power supply
disconnected. At the end of each work session, or when required,
remove any dust from the body of the tool using a jet of compressed
air, paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by the user.
Maintenance and cleaning of the inner parts, like brushes, ball bearings, gears
etc. or others, must be carried out only by an authorized customer-service
workshop or on www.rupes.com.
Use only the original RUPES parts or accessories.
DISPOSAL
For EC countries only: According to the European Directive on Waste
from electrical and electronic equipment and its implementation in
conformity with national standards, exhausted electrical equipment
must be collected separately, in order to be recycled in an environmentally friendly
way. The product, when it reaches the end of its life, must not be dispersed in the
environment or thrown away as household waste. It must be disposed at
authorized recycling centres (contact your local authorities to know where to
dispose of the product according to the law). The correct disposal of the product
contributes to the health and preservation of the environment.
Illegal disposal of the product will entail penalties against the offenders.
Disposing of the product correctly contributes to protecting human health and
safeguarding the environment. Any illegitimate disposal of the product will be
punishable by law.
CONFORMITY DECLARATION
We declare on our responsability that the hand-held motor operated tool, which
is mentioned in the present operating manual, is in comformity with the Essential
Requirements of Safety of the following Directives:
2006/42/CE; 2006/95/CE; 2004/108/CE; 2011/65/CE.
The tests have been carried out in accordance with following Standards:
EN 60745-1: 2009 + A11: 2010
EN 60745-2-4:2009+ A11:2011.
EN 55014-1: 2006 + A1: 2009 + A2: 2011
EN 55014-2: 1997 + A1: 2001 + A2: 2008
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009
EN 61000-3-3: 2008
EN 50581: 2012
Technical file at:
RUPES S.p.A.
Via Marconi, 3A
20080 VERMEZZO (Mi) - Italy
Vermezzo (MI), 01/01/2015
S.p.A
IL PRESIDENTE
G. Valentini
Publicidad
