General Information; Important Parts; User Instructions - DeVilbiss Healthcare Innova 50166 Manual De Usuario

gENERal INFoRMaTIoN

CONTENTS: Innova Nasal Vented Mask with headgear
This product is not manufactured with natural rubber latex
Rx ONLY MADE IN U.S.A.
The Innova Vented Nasal Mask is intended to provide an interface for application of positive airway pressure therapy, such
as CPAP or bilevel. The mask is intended for single patient use in the home or multi-patient use in the hospital or
institutional environment on adult patients (>66lbs/30kg) for whom CPAP or bilevel therapy has been prescribed. The mask
has a non-transferable three month limited warranty for manufacturer's defects from the date of purchase by the initial
consumer. If a mask used under normal conditions should fail, DeVilbiss will replace the mask or its components. For
additional information about the DeVilbiss Warranty, please visit http://www.devilbisshealthcare.com.
NOTE: The mask has a service life of 6 months.
NOTE: Please dispose of the mask and accessories in accordance with local and regional guidelines.
NOTE: THIS PRODUCT IS NOT MANUFACTURED WITH NATURAL RUBBER LATEX

IMpoRTaNT paRTS

Innova Mask
1. Touchless Spacebar™
2. Mask Shell
3. Airgel™ Cushion
4. Quick Release Headgear Connector
5. Vented Elbow Assembly
6. Active Headgear Connector™
uSER INTRucTIoNS
1. Remove the mask and the headgear from the package.
2. Place the headgear on a table, label side down with the narrowest part close to you.
3. Set the mask with the gel side down onto the center of the headgear.
4. Take each headgear strap and connect it to its respective location on the mask by looping the Velcro strap through
the headgear slots and attaching it back to itself (Figure 1).
5. Once the headgear has been properly attached to the mask, follow the fitting tips below to fit the mask:
6. Detach one Velcro strap by sliding the Velcro loop off the quick release hook, slip the headgear over the head and
center the mask on the face.
7. Find the detached Velcro strap and slide the Velcro loop back on the quick release hook (Figure 2).
8. Be sure the headgear straps are parallel and the headgear is fully extended and flat across the back of the head
(Figure 3).
9. Adjust the bottom headgear straps by using the Velcro tabs. Make sure the Active Headgear Connector is parallel to
the face and that there is equal tension from the headgear on both sides. After tightening, make sure the Active
Headgear Connector can move freely (Figure 4).
NOTE: Do NOT over tighten the headgear.
NOTE: The Touchless Spacebar will be tilted away from the face after tightening the bottom straps.
10. Adjust the upper headgear straps by using the tabs. Be sure they are tightened evenly and that the Touchless
Spacebar is parallel to the forehead (Figure 5).
NOTE: The Touchless Spacebar should NOT touch the forehead. It should be parallel to the forehead (Figure 6).
11. Adjust the bottom headgear straps to make sure the bottom of the mask is seated comfortably on the face.
12. For optimal seal and comfort, mask should be snug but not tight. Adjust the tension by detaching the Velcro straps,
tightening or loosening the straps, and reattaching the Velcro .
13. Connect the mask tubing assembly to the positive airway pressure device tubing and turn the device on to the
prescribed pressure (Figure 7).
14. Turn head from side to side while lying on the bed and identify areas of leak that may prevent sleep.
15. In the event of leaks, tighten the Velcro tabs closest to the area of leak. Do NOT over tighten the headgear.
4
1
6
5
4
2
3
90147