Descargar Imprimir esta página

Rupes BA215S Traducción De Manual De Instrucciones Original página 12

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 23
WARNING: never press the wheel spindle locking button until
the tool has stopped moving and is perfectly stationary; the gear
box or the push button pin could be broken and the guarantee
would be invalidated.
2.Mode
lock the wheel spindle (4) by inserting the 17 mm spanner in the nocth
in the spindle between the wheel and the gearbox. Unscrew the
locking ring using the pin wrench, replace the wheel, re-tighten the
locking ring.
Tools other than those mentioned must not be used for slackening for
tightening purposes.
WARNING: Before use, check the state of the wheel. The wheels
must be properly assembly and must rotate freely rotate freely.
Never use defective or damaged wheels/cutters. Defective
wheels can fall to pieces and cause dangerous incidents.
Start the tool and check that there are no unusual vibration, no dismatching
movement of the abrasive disc. Otherwise switch-off the tool immediately and
eliminate the cause.
STARTING AND STOPPING
- Starting: push the slide of the ON/OFF (2) forward; if the tool is to be locked in
the ON position, apply pressure to the front part of the slide switch at the same
time.
- Stopping: release the slide ON/OFF (2).
If locked, press the ON/OFF switch in the lower part downwards and release it
in the OFF position.
WARNING: after an interruption of the electrical energy, if the
ON/OFF switch is inserted, it is necessary to release the switch
(see Stopped).
ACCESSORIES
BA215N
Ø 115 mm depressed centre type abrasive wheels.
BA225N
Ø 125 mm depressed centre type abrasive wheels.
The use of tools of larger diameter will overload the motor and
drive system leading to rapid deterioration.
12
MAINTENANCE
All maintenance operations are carried out with the power supply
disconnected. At the end of each work session, or when required,
remove any dust from the body of the tool using a jet of compressed
air, paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by the user.
Maintenance and cleaning of the inner parts, like brushes, ball bearings, gears
etc. or others, must be carried out only by an authorized customer-service
workshop or on www.rupes.com.
Use only the original RUPES parts or accessories.
DISPOSAL
For EC countries only: According to the European Directive on Waste
from electrical and electronic equipment and its implementation in
conformity with national standards, exhausted electrical equipment
must be collected separately, in order to be recycled in an environmentally friendly
way. The product, when it reaches the end of its life, must not be dispersed in the
environment or thrown away as household waste. It must be disposed at
authorized recycling centres (contact your local authorities to know where to
dispose of the product according to the law). The correct disposal of the product
contributes to the health and preservation of the environment.
Illegal disposal of the product will entail penalties against the offenders.
Disposing of the product correctly contributes to protecting human health and
safeguarding the environment. Any illegitimate disposal of the product will be
punishable by law.
CONFORMITY DECLARATION
We declare on our responsability that the hand-held motor operated tool, which
is mentioned in the present operating manual, is in comformity with the Essential
Requirements of Safety of the following Directives:
2006/42/CE; 2006/95/CE; 2004/108/CE; 2011/65/CE.
The tests have been carried out in accordance with following Standards:
EN 60745-1: 2009 + A11: 2010
EN 60745-2-3:2011+ A2:2013
EN 55014-1: 2006 + A1: 2009 + A2: 2011
EN 55014-2: 1997 + A1: 2001 + A2: 2008
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009
EN 61000-3-3: 2008
EN 50581: 2012
Technical file at:
RUPES S.p.A.
Via Marconi, 3A
20080 VERMEZZO (Mi) - Italy
Vermezzo (MI), 01/01/2015
S.p.A
IL PRESIDENTE
G. Valentini

Publicidad

loading

Este manual también es adecuado para:

Ba225s