Introduction; Manual Purpose And Contents; Target; How To Keep This Manual - KENT Razor Plus 24D Instrucciones De Uso

INSTRUCTIONS FOR USE

INTRODUCTION

MANUAL PURPOSE AND CONTENTS

The purpose of this manual is to provide the operator with all
necessary information to use the machine properly in a safe
and autonomous way. It contains information about technical
characteristics, operation, machine storage, maintenance,
spare parts and safety conditions.
Before carrying out any procedure on the machine, the
operators and technicians in charge of the maintenance must
read this manual carefully. Contact an authorized Kent
Service Center in case of doubts regarding the interpretation
of the instructions and for any further information.

TARGET

This manual is intended as a guide for the operator and the
technicians qualified to perform the machine maintenance.
The operators must not carry out operations reserved for
qualified technicians. Kent will not be answerable for
damages coming from the non-observance of this prohibition.

HOW TO KEEP THIS MANUAL

The Instructions for Use Manual must be kept near the
machine, inside an adequate case, away from liquids and
other substances that can cause damage to it.

IDENTIFICATION DATA

The machine model and serial number are marked on the
plate on the tank and can be read from the outside (1, Fig. C).
The machine model year is shown after the Date Code on the
serial plate (A05 means January 2005).
This information is useful when requiring machine spare
parts. Use the following table to write down the machine
identification data for any further reference.
MACHINE model .............................................................
MACHINE serial number .................................................

OTHER REFERENCE MANUALS

Electronic Battery Charger Manual, which is to be considered
an integral part of this Manual.
Moreover, the following manuals are available:
– Service Manual, that can be consulted at Kent Service
Centers.
– Spare Parts List, supplied with the machine.

SPARE PARTS AND MAINTENANCE

All necessary operating, maintenance and repair procedures
must be carried out by qualified personnel or by Kent Service
Centers. Only original spare parts and accessories must be
used.
Call Kent for service or to order spare parts and accessories,
specifying the machine model and serial number.

CHANGES AND IMPROVEMENTS

Kent constantly improves its products and reserves the right
to make changes and improvements at its discretion without
being obliged to apply such benefits to the machines that
were previously sold.
Any change and/or addition of accessory must be approved
and performed by Kent.
2 Razor™ Plus 24D-26D-28D / Razor™ Plus 24C-28C — 909 5428 000(2)2005-01

SAFETY

The following symbols indicate potentially dangerous
situations. Always read this information carefully and take all
necessary precautions to safeguard people and property.
The machine Operator's cooperation is essential in order to
prevent injury. No accident prevention program is effective
without the total cooperation of the person responsible for the
machine operation. Most of the accidents that may occur in a
factory, while working or moving around, are caused by
failure to comply with the simplest rules for exercising
prudence. A careful and prudent Operator is the best
guarantee against accidents and is essential for successful
completion of any prevention program.

SYMBOLS

DANGER!
It indicates a dangerous situation with risk of
death for the Operator.
WARNING!
It indicates a potential risk of injury for people.
CAUTION!
It indicates a caution related to important or
useful functions. Pay attention to the
paragraphs marked by this symbol.
NOTE
Refer to the manual before performing any
operation.

GENERAL INSTRUCTIONS

Description of potential risk of damages to people and
machine.
DANGER!
– Before performing any maintenance/repair operation,
disconnect the battery.
– This machine must be used by properly trained and
authorized personnel only. Children or disabled people
cannot use this machine.
– Keep the battery far from sparks, flames and
incandescent material. During the normal operation
explosive gases are released.
– Do not wear jewelry when working near electrical
components.
– Do not work under the lifted machine without support it
with safety stands.
– Do not operate the machine near toxic, dangerous,
inflammable and/or explosive powders, liquids or
vapors.
– Battery charging produces highly explosive hydrogen
gas. Keep the tanks open during battery charging and
perform this operation in well-ventilated areas and away
from naked flames.