Weber original 17587 Manual Del Usuario página 5

DIGITAL MEAT THERMOMETER, WIRELESS
2. Press and hold the POWER / LIGHT button for 3 seconds to switch on the monitor.
3. Press and hold the
the transmitter is turned on, a red LED light on the transmitter will flash fast one time
followed by 2-3 flashes. The current temperature will be displayed on the monitor.
4. Press the MEAT button to select type of meat. The monitor displays the type of meat, the
thermometer is ready to measure. Each press will change the display in the sequence as
shown in ILLUSTRATION 9 PAGE 3.
5. To select the doneness level of the meat, press the TASTE button. The different taste options
are: WELL / M WELL / MEDIUM / M RARE / RARE. The corresponding preset temperature will
show on the monitor as "Target Temp".
6. To manually set the target temperature:
Press and hold the MODE button for 3 seconds, "Target Temp" will start to flash.
Press MIN (+) or SEC (-) buttons to select the desired temperature.
Press the MODE button to confirm your setting.
NOTE: Once the desired temperature is reached, the monitor will start to beep and the
"Current Temp" will begin to blink.
• To stop the alarm temporarily, press the MODE button.
• To stop the alarm completely, remove the probe from the meat.
NOTE: The maximum operating temperature for the probe is 380°C (716°F). When the probe
temperature exceeds the maximum display temperature (300°C / 572°F) the LCD will show "HHH".
AFTER COOKING
• Once cooking is finished, remove the probe from the meat using oven mitt or gloves.
• Press and hold POWER / LIGHT on the monitor and
to turn them off. The transmitter will flash 3 times continuously.
• Disconnect the probe from the transmitter and replace the socket cover.
CLEANING
Clean the probe, monitor and transmitter by wiping with a damp cloth and mild detergent.
NOTE: Do not clean the probe, monitor or transmitter in a dishwasher or immerse in water or
liquid.
TO OPERATE THE TIMER
The count up and count down timer operate independently of the temperature sensor.
To start the count up timer press the TIMER button when 00:00 is displayed on the monitor. To
stop the timer, press the TIMER button. To restart after stopping, press TIMER button. To reset
to 00:00, press the TIMER button followed by the CLEAR button.
To start the count down timer, first set the minutes and seconds. Press the MIN button to set
the minutes and press the SEC button to set the seconds. Press the TIMER button to start the
count down. To stop the count down, press the TIMER and to restart, press the TIMER again.
To reset press the TIMER followed by the CLEAR button. Once the count down has finished, the
monitor will beep and the MIN:SEC will flash on the screen. Press any button to stop the
alarm.
BACKLIGHT
Press the POWER / LIGHT button to illuminate the screen for 5 seconds.
NOTE: The backlight will turn on when any button is pressed, but then settings will also
change.
TRANSMITTER DATA TRANSMISSION
Place the transmitter within 60 m (196 ft) of the monitor.
NOTE: The LED indicator flashes during transmission.
IMPORTANT: The transmitter will transmit the temperature every 30 seconds if the
temperature does not change. Once the temperature changes the transmitter will update
automatically.
PRECAUTIONS
This product is engineered to give you years of satisfactory service if you handle it carefully.
Here are a few precautions:
• Do not subject the unit to excessive force, shock, dust, temperature or humidity, which may
result in malfunction, shorter electronic life span, battery damaged or deterioration of parts.
• Placement of this product on wood surfaces with certain types of finishes, such as clear
varnish, may result in damage to the finish. Consult the furniture manufacturer's care
instructions for direction as to the types of objects that may safely be placed on the wood
surface. Weber-Stephen Products Co. shall not be responsible for any damage to wood
surfaces from contact with this product.
• Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft,
lint-free cloth.
• Do not clean the unit with abrasive or corrosive materials.
• Do not use the thermometer in a microwave oven or oven.
WWW.WEBER.COM
®
button on the top of the transmitter to switch on the transmitter. Once
on the transmitter for about 2 seconds
5