Troy-Bilt TB22 EC Manual Del Operador

Removing Unit From Carton Assemble The Unit
Slot
Bracket
1 1 2
Remove all contents from Slide shield's slot onto
carton. mounting bracket. Rotate
shield onto shaft. Push
square bolt through shield
and bracket. Tighten
washer and wing nut
onto bolt.
Assemble The Unit
40:1
1 Gallon 3.2 oz
5 6
Mix thoroughly in separate Place unit on a level surface.
fuel can: Fill fuel tank.
– 3.2 fl. oz. of 2-cycle
engine oil
– 1 gallon of unleaded
gasoline (less than 30
days old)
NOTE: Do not mix directly in
fuel tank.
Starting The Unit
1 9 10
Crouch in starting position. SQUEEZE and HOLD
throttle for ALL further
steps.
Reloading the Line*
Outer
Bump
Spool
Knob
Inner
Spring
Reel
1 1 2
Unscrew the bump knob Remove the inner reel and
counterclockwise. spring.
Reloading the Line
For replacement line, call 1–800-800-7310 or go to
an authorized service dealer.
For single line installation or replacement spool
installation instructions, refer to the Replacing the
Trimming Line section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions
are NOT part of the fast assembly instructions. Line does not need to
be installed on the initial assembly and start-up.
1 8
Hold the inner reel and outer
spool together. Firmly pull the
two line ends to release them
from the holding slots. Screw
the bump knob on clockwise.
Tighten the bump knob
securely.
IMPORTANT: READ THE OPERATOR'S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
NEED HELP?
769-08425 / 00
Operator's Manual
Min. 6"
3 4
Remove cap from lower Push the handle onto the shaft
housing. The bolt hole should be
boom. Push cutting
to the right. Insert the bolt into the
attachment into coupler.
bolt hole. Tighten the bolt, but not
Turn coupler knob clockwise
completely. Move the handle to
to tighten.
the location that provides the best
grip. Move the handle a minimum
of 6 inches away from the shaft
grip. Tighten the bolt until the
handle is secure.
Starting The Unit
Primer
Choke Lever
Bulb
10 X
7 8
Press primer bulb 10 times, Move choke lever to
or until fuel is visible Position 1.
Choke Lever
5 X
11 12
Pull rope 5 times. Move choke lever to
Position 2 and squeeze
throttle.
Top Hole
Bottom Hole
3 4
Cut one 6-foot (1.8 m) length Insert the end of one line into
of new 0.095" split line the top hole and the end of
trimming line. Split each end the other line into the bottom
about 6 inches (150 mm). hole.
CALL 1-800-828-5500 IN U.S. OR 1–800–668–1238 IN CANADA
TB22 EC
2-Cycle Trimmer
Electric Starter or
Power Start Bit Optional!
THESE OPTIONAL ACCESSORIES
Starter Rope
ARE SOLD SEPARATELY!
This unit has an alternate starting method
that many find easier to use than pulling a
rope. Please contact a local retailer or call
1-800-828-5500 for more information.
On/ Off Switch
Information may also be found at
D-Handle
www.troybilt.com
ASSEMBLY TOOLS
REQUIRED:
• 3/8" Socket
Coupler
Cutting Head Shield
Choke Lever
3-5 X
13 14
Pull rope 3-5 times to start Continue to squeeze
engine. Run unit for 30-60 throttle. Move choke lever
seconds to warm up. to Position 3.
Holding Slots
Split Wall
5 6
Wind the line tightly in the Insert the two 6-inch sections
direction shown on the inner into the two .095 holding
reel. The split wall will divide slots.
the line. Wind the line until it
is completely divided and
about 6 inches (150 mm) of
line remains.
Fuel Cap
Throttle Control
Need Help?
Call 1-800-828-5500
DIDN'T START?
Repeat these instructions.
IF engine fails to start after 2 attempts,
move choke lever to position 3 and pull
the starter rope until engine starts
IF unit still fails to start, refer to the
operator's manual for additional starting
and troubleshooting information
15
Continue to squeeze
throttle. Run unit for an
additional 60 seconds to
complete warm-up. Unit
may be used during this
time.
Eyelets
7
Pass the two line ends
through the eyelets. Place the
spring inside the inner reel.
Insert the inner reel into the
outer spool. Push the inner
reel and outer spool together.
09/12