Publicidad
Idiomas disponibles
Idiomas disponibles
DELIVERY CONTENTS - SUPERTRAPEZE
SP408 - SUPPORT ARM
24. Support Arm Weldment
25. Rectangular Plug
26. Plastic Buckle
27. Safety Strap
SP409 - TRAPEZE ASSEMBLY
28. Trapeze Handle
29. Top Grip, 6" length
30. Bottom Grip, 10" length
INSTALLATION WARNINGS
1. Use caution while maneuvering pole during installation.
2. Standard pole can be installed directly under 1 ceiling joist.
3. Standard pole can be installed directly under 2 ceiling joists.
4. Heavy Duty (HD) pole must be secured to ceiling joist (s).
5. If subject to heavy usage, pole must be secured to ceiling joist (s).
6. CAUTION - Damage may occur if extension screw is overtightened.
7. CAUTION - Do not install if the structure above ceiling is unknown.
8.CAUTION - Do not install on loose floor coverings.
9. CAUTION - Do not install in rooms with radiant ceiling heat.
10. CAUTION - Do not install on angled ceilings.
SUPERPOLE PLACEMENT
1. BEDROOM - Locate pole adjacent to waistline, and as close to bed as
possible while allowing clearance for bed coverings.
2. BATHTUB ONLY - Locate pole base against tub, approximately half way
along its length
3. SEATING (TOILET or CHAIR) - To provide clearance when standing,
locate pole 3-10" / 76mm-254mm forward of the knees, and 2-6" /
51mm-154mm to the side of knees when sitting.
SUGGESTED SUPERBAR POSITIONS
4. BEDROOM
A = side support / out of the way
B = in-bed support
C = sitting support
D = standing support
E = transfer support to
walker / wheelchair
SUPERPOLE INSTALLATION INSTRUCTIONS
1. On a flat horizontal surface, place top plate onto pole.
2. Align holes and install clevis pin with washer on opposite side.
3. Install cotter pin into clevis pin.
4. Place base plate on floor at intended location, and tilt pole.
5. When upright, install the pole into the base plate hole.
6. Insert shaft of screwdriver thru drive hole of extension screw.
7. Hold pole and turn screwdriver clockwise to raise pole.
8. Top plate must contact ceiling squarely.
9. Continue turning extension screw approx 2-5 turns until pole is secure.
10. Turn jam nut until it is tight against bottom of pole.
11. Turn both jam nut and extension screw together to jam tight.
12. Remove screwdriver and lower cover sleeve to conceal screw.
FIGURE C.
HARDWARE
18. 5/16-24 Set Screw (x4)
23. 5/32" Hex Key
FIGURE D.
FIGURE E.
FIGURE E.
5.BATHROOM or 6.SITTING
A = side support / out of the way
B = standing or transfer support
C = standing support
D = standing or transfer support
E = standing or transfer support
F = transfer support in/out of bathtub
FIGURE F.
English
SUPERBAR INSTALLATION INSTRUCTIONS
1. Slide spring ring upwards on castellated collar to expose 3 set screws.
2. Back off 3 cone point set screws with hex key so castellated collar can
slide onto pole without set screws contacting pole.
3. Install pivot bushing into T-bar assembly.
4. Align hole and install screw with hex key.
5. Remove cover sleeve from bottom of pole.
6. Slide items onto bottom of pole (note order and orientation): T-Bar
assembly with installed pivot bushing top/first, spring ring with
castellated collar, pivot bushing and cover sleeve.
7. Install SuperPole as per instructions Page 6-7.
8. Install castellated collar to pole by tightening 3 set screws with hex key.
The set screws MUST be tightened until the back of the screw is flush
with the collar or injury may result.
9. Slide spring ring downwards on the castellated collar to retain set screws.
10. Lower T-bar assembly onto castellated collar.
11. Install bottom pivot bushing into T-bar assembly.
12. Align hole and install screw with hex key.
SUPERTRAPEZE INSTALLATION INSTRUCTIONS
1. Slide support arm onto top of pole with strap hook facing towards grip.
Rest support arm on top of grip.
2. Install SuperPole as per instructions Page 6-7.
3. Rotate support arm over bed.
4. Hold the trapeze handle under the support arm, such that the shorter rail
of the handle is closest to the head of the bed.
5. Rotate the strap 180° and slide onto the shorter rail of the trapeze
handle until it reaches the top bend of the trapeze.
6. Position support arm such that the trapeze handle hangs directly over
the user's hands (on thighs) when they lay on the bed.
7. Raise support arm approx 84"/2134mm from floor to top of support arm.
8. Slide spring ring upwards on support arm to expose threaded holes.
9. Install support arm to pole by tightening 3 set screws with hex key. The
set screws MUST be tightened until the back of the screw is flush with
the collar or injury may result.
10. Slide spring ring downwards on the castellated collar to retain set screws.
11. Adjust length of strap such that the user can comfortably grasp the
bottom rail of the trapeze handle when laying down.
TECHNICAL DATA
See Figure I.
PRODUCT COMPATIBILITY CHART
See Figure J.
PRODUCT USAGE
See Figure I.
FIGURE G.
FIGURE H.
15
Publicidad
