Publicidad
OVERVIEW
Thank you for choosing the Invisia Shampoo Shelf. Please read and
understand the instructions in this manual; keep manual for future
reference. It is your responsibility to see that your Invisia Shampoo Shelf is
properly assembled, installed, and cared for. Failure to follow instructions in
this manual could result in serious injury or death. If you are not equipped
to undertake the outlined work, we would recommend that you have your
Invisia Shampoo Shelf installed by a qualified contractor.
The Invisia Shampoo Shelf is a combination grab bar and shelf, designed
to disguise safety in a bathroom accessory. The Invisia Shampoo Shelf is
intended for moderate vertical and horizontal load bearing to provide sitting
and standing support for people with reduced mobility. The Invisia
Shampoo Shelf is installed with appropriate fasteners to a structural wall.
The tray (which holds bottles) is NOT intended to be a support product.
The maximum user weight for this product is 500lbs / 227kgs. Note:
Product is not intended to support full body weight. The Invisia Shampoo
Shelf is not to be used in any other way than described above.
LIMITED LIFETIME WARRANTY
Products are covered by a limited lifetime warranty against defects in
materials and workmanship for the original purchaser. Warranty excludes
products that have been damaged through misuse, accidental damage,
alteration, normal wear and tear, wood material and stain, or the use of
corrosive or abrasive cleaning products.
Buyer hereby indemnifies, agrees to hold harmless and defend HealthCraft
Products Inc. from and against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including without
limitation consequential damages and reasonable professional fees)
resulting from buyers specification, application, or improper use of goods
described hereon; buyers omission or neglect. HealthCraft Products Inc.
does not assume any liability for damage resulting from services performed
by others or faulty installation, misuse or misapplication of goods sold by
HealthCraft Products Inc. HealthCraft Products Inc. shall not be liable for
prospective profits or special, indirect, or consequential damages, or for the
cost of any corrective work done without HealthCraft Products Inc. prior
approval. HealthCraft Products Inc. total liability hereunder shall in no
event exceed the purchase price of the goods specified hereon.
Specifications subject to change without notice.
HealthCraft Products Inc.
2790 Fenton Road
Ottawa, Canada
K1T 3T7
DELIVERY CONTENTS / SHAMPOO SHELF
1. Rail (Shampoo Shelf)
2. Wall Stem Assembly (x2)
3. #10-32 Set Screw (x2)
4. Shelf
5. Center Punch
6. 3/32" Hex Key
10
English
Gate 88
Kanalgatan 45B
Skellefteå, Sweden
EC
REP
93123
FIGURE A.
7. Lock Washer, S/S (x2)
8. Plastic Cap (x2)
9. Rubber Bumper (x2)
10. #10 x 3" Wood Screw, S/S (x2)
11. #10 x 2" Wood Screw, S/S (x2)
INSTALLATION WARNINGS
1. Rail must be installed to walls that are structurally sound.
2. If desired installation location does not have adequate structure, add
wood blocking.
3. CAUTION - Do not install if there is no structure for one side.
4. CAUTION - Do not install if there is no structure behind drywall.
5. CAUTION - Do not install if structure behind walls is unknown.
6. CAUTION - Do not install into metal studs.
7. CAUTION - Do not install in fiberglass / acrylic shower enclosures with
insufficient stiffness and strength.
8. CAUTION - Rail and bathtub are slippery when wet.
SUGGESTED SHAMPOO SHELF LOCATIONS
To determine the optimal mounting location, we recomment holding the rail
in place and walking through the motions of a transfer (sitting, standing,
reaching ,etc.). Recommended rail height 36-48" / 914-1219mm.
INSTALLATION
1. Back off set screws from rail sockets.
2. Allow wall stems to freely move in and out of rail sockets.
3. Peel off label on back of wall stems to expose sticker.
4. With wall stems inside rail sockets, push the rail against the wall.
Ensure level.
5. Firmly press the rail so stickers on back of wall stems contact wall.
6. Remove rail carefully so wall stems stay on the wall.
7. Using wall stems as locating guides, mark the tile with center punch.
8. Drill pilot holes for fasteners. Fasten the wall stems to the wall using
appropriate fasteners and waterproofing.
9. Place rail back onto the fastened wall stems.
10. Secure rail to wall stems by tightening set screws.
11. Using wall plate as a locating guide, mark the tile with center punch
and drill pilot holes for fasteners.
12. Secure rail to wall by lower holes.
13. Cover screw heads with plastic caps (x2). Inspect hardware regularly,
and tighten if required.
14. Remove protective sheet on rubber bumper to expose adhesive, and
place (adhesive facing upward) on spoke of rail.
15. Slide tray in from the side, center with rail and lower onto bumpers so
the adhesive sticks to the bottom of the tray.
TECHNICAL DATA
See Figure E.
PRODUCT USAGE
See Figure F.
FIGURE B.
FIGURE C.
FIGURE D.
Publicidad
