Publicidad
Idiomas disponibles
Idiomas disponibles
9
.
2
.
- ELECTRICAL DIAGRAM
9
.
2
.
-
9.3.- EXPLODED VIEW
See page 13
10.- TROUBLESHOOTING
FAILURE OR MALFUNCTION
Equipment starts up but doesn't
aspirate.
Equipment starts up but suction is not
enough or inexistent.
Failure continues..
Equipment doesn't start up nor the
luminous switch lights up.
Failure continues.
11.- TECHNICAL SPECIFICATION, EMC INFORMATION
Guidance and manufacturer's declaration – electromagnetic emissions
The system is intended for use in the electromagnetic environment specified below.
The customer or the user of the equipment should assure that it is used in such an environment.
Emissions test
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC61000-3-2
Voltage fluctuations/ flicker
emissions
IEC61000-3-3
Guidance and manufacturer's declaration – electromagnetic immunity
The equipment is intended for use in the electromagnetic environment specified below.
The customer or the user of the equipment should assure that it is used in such an environment.
I
test
MMUNITY
Electrostatic
discharge (ESD)
IEC61000-4-2
Electrical fast
transient/burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, short
interruptions and
voltage variations
on power supply
input lines
IEC 61000-4-11
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
Regulation control is open.
Suction tube wrongly inserted..
Cap improperly adjusted.
Bacterial filter is saturated.
Entry of liquid inside the pump.
Examine the fuse possible deterioration and
Electromagnetic environment – guidance
Compliance
Grup 1
The equipment uses RF energy only for its internal function. Therefore,
its RF emissions are very low and are not likely to cause any
interference in nearby electronic equipment.
Class B
The equipment is suitable for use in all establishments, including
domestic establishments (not industrially) and those directly connected
Class A
to the public low-voltage power supply network that supplies buildings
used for domestic purposes.
Complies
IEC 60601
test level
±6kV contact
±8kV air
±2kV for power supply lines
±1KV for input/output lines
±1kV line(s) to line(s)
±2kV line(s) to earth
<5%U
(>95% dip in U
for
T
T)
0,5 cycle
<40%U
(>60% dip in U
for
T
T)
5 cycles
<70%U
(>30% dip in U
for
T
T)
25 cycles
<5%U
(>95% cycles U
for
T
T)
5 s
3 A/m
CAUSE
the power plug.
?
Compliance level
±6kV contact
±8kV air
±2kV for power supply
lines
±1kV line(s) to line(s)
±2kV line(s) to earth
Ídem
3 A/m
SOLUTION
Close control.
Insert correctly.
Adjust properly.
Change filter.
Disassembly and cleaning of pump
head by Technical Services.
Replace the fuse or the plug.
Contact Technical Services.
Electromagnetic environment
guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered with
synthetic material, the relative humidity
should be at least 30 %.
Mains power quality should be that of a
typical commercial or hospital
environment.
Mains power quality should be that of a
typical commercial or hospital
environment.
Mains power quality should be that of a
typical
commercial
or
hospital
environment.
If
the
user
of
equipment requires continued operation
during power mains interruptions, it is
recommended that the equipment be
powered from an uninterruptible power
supply or a battery.
The power frequency magnetic field
should be measured in the intended
installation location to assure that it is
sufficiently low.
Página 12 de 13
the
Publicidad
