B&G electronics PW-150 Manual Del Usaurio página 2

PW-150/250 PW-150/250
V5 V5
COMPONENTS AND RECOMMENDED LOCATIONS IN THE VEHICLE
(1) Electronic unit
(1) Control keyboard & internal microphone
(1) 150W loudspeaker / (2) 150W loudspeakers
(2) External microphones
(2) Internal speakers
(1) Keyboard harness
(1) Power cable (battery)
(1) Fuse 25A
(2) Speaker extension cables
(1) Loudspeaker and auxiliary load harness
(1) Hand microphone (optional)
(1) Hand microphone holder (optional)
INSTALLATION AND ELECTRIC DIAGRAM
To install the equipment, see the wiring diagram shown further on.
Avoid leaving visible cables in the cabin to maintain the vehicle's aesthetics unaffected.
If there are any cables left disconnected, insulate them with tape; disconnected cables
making an undesired contact can cause a malfunction.
Electronic Unit
Place it on a hidden location for aesthetic purposes. Make sure that the location
allows some ventilation into the unit to avoid overheating.
Digital Keyboard
To facilitate the handling of the equipment, place the keyboard on a location within
the driver's reach, such as the console of the vehicle. Clean the surface where the
keyboard is to be sticked to ensure an adequate adherence. Remove the protective
liner from the adhesive pad in the back side and stick it to the surface.
To clean the keyboard, gently wipe it with a dry cloth. Do not use water or any solvent.
Loudspeaker
When selecting the location for the loudspeaker, keep in mind that this component is
suitable for outdoor use but not immersion-proof.
The loudspeaker must be placed as far as possible from the keyboard (where the
internal microphone is located) in order to avoid feedback.
External Microphones
The microphones require an assembly procedure, shown on the next page.
There are two recommended locations to place them, see the installation instructions
on the next page.
Internal Speakers
Place them at opposing sides inside the vehicle to get a stereo sound. Locate the
speakers out of view, without affecting the sound.
Hand microphone (optional)
Place the hand microphone holder within easy reach of both driver and passenger.
EXTERNAL MICROPHONES INSTALLATION INSTRUCTIONS
Shell
Microphone
Mounting
tape
INTERNAL SPEAKER EXTERNAL MIC
CONTROL KEYPAD
& INTERNAL MIC
(2) 150W
LOUDSPEAKERS
150W
LOUDSPEAKER
ELECTRONIC UNIT
PW-150/250
INTERNAL SPEAKER EXTERNAL MIC
Each microphone includes a shell to hold it
in place and protect it from the elements.
Depending on the installation procedure,
it can be more convenient to assemble
microphone and shell either before or after
the wiring.
For instance, if the wiring requires to pull
the cable through a narrow space, it is
recommended to assemble after wiring.
2 2 PW-150/250 PW-150/250
V5 V5
Microphone + shell assembly procedure
1. Insert the cable in the shell by pressing it with your fi nger.
3. Remove the liner from the tape and stick it to the shell.
Location A
Inside the rearview mirror.
This location offers the highest
sound volume, yet the most
time consuming installation, as
it requires to take parts of the
vehicle apart.
Location B*
In the gap of the front doors.
Select a surface to place the
microphone, so that it faces to
the exterior from inside the gap.
Once the surface is selected,
the installation is fairly easy.
* WARNING!
On location B, place the
microphone slightly
downward to prevent
damage from water
clogging.
2. Push the microphone into the shell (do not pull the cable!).
4. Stick the shell on the selected surface, previously cleaned
with a 1:1 solution of isopropyl alcohol in water.
Recommended spots to install the microphones
There are two recommended spots in the vehicle (see
fi gure to the left), they differ with regard to ease of
installation and audio reception volume.
You can select a location according to your
preferences.
3 3