Silverline 660471 Manual De Instrucciones página 7

660471
• The Motor Housing (12) will slide vertically along the Plunge Rail (14)
increasing/decreasing distance from the Low Friction base (1)
Accessory installation
WARNING: Only use accessory bits with a shank diameter that is designed
specifically for the diameter of Collet (2) installed on this machine.
1. With the tool off and disconnected from the mains, depress the Spindle Lock
Button (5) and turn the Collet (2) until it locks into position
2. Loosen the Collet using the Collet Spanner (21) and insert the accessory
Shank (16) into the Collet
3. Ensure at least half of the Shank's length is inserted into the Collet
4. Securely tighten the Collet using the Pin Spanner whilst holding down the
Spindle Lock Button
Guide fence installation
• Use the Fence (23) in order to create straight cuts parallel to a straight edge
1. Insert the Graduation Scale (22) into the holes located in the Low Friction
base (1), (Image A)
2. Secure the Graduation Scale in place by fastening the Guide Fence Securing
Knobs (4)
• The Graduation Scale is marked to accurately measure cutting distances.
Align the Collet (2) with the marking on the Graduation Scale to set a cutting
distance from the Fence
Dust extraction
WARNING: Always connect the tool to a suitable vacuum cleaner or workshop
dust extraction system if the sanding dust contains harmful substances, such as
particles from old paint, varnish, surface coatings etc. Always dispose of harmful
dust according to laws and regulations.
WARNING: Take special care to guard against harmful and toxic dusts when
sanding lead-based painted surfaces, woods and metals, particularly if you are
unsure about the exact substances involved. All persons entering the work area
must wear a mask specially designed for protection against the toxic dust and
fumes involved. Children and pregnant women MUST NOT enter the work area. DO
NOT eat, drink or smoke in the work area.
• This tool is designed to be connected to a household vacuum cleaner hose
or workshop dust extraction system. This is the preferred and most effective
method of dust extraction
• Insert the small tapered end of the Dust Extraction Adaptor (3) in to the Dust
Extraction Port (15)
• Connect a suitable vacuum hose to the Dust Extraction Adaptor (3)
Note: The Dust Extraction Port is designed to fit a 32mm diameter hose.
Operation
WARNING: ALWAYS wear eye protection, adequate respiratory and hearing
protection, as well as suitable gloves, when working with this tool.
Switching on and off
• To turn the machine on, press and hold the On/Off Trigger Switch (9)
• To turn the machine off, release the On/Off Trigger Switch
• This machine features a Lock On Button (10), to use the Lock On Button:
1. Hold the On/Off Trigger Switch and press the Lock On Button
2. To turn the machine off, press and release the On/Off Trigger Switch
Speed adjustment
Note: The speed of this tool can be adjusted to suit the material of the workpiece.
• To adjust the speed, move the Speed Control Dial (7) until you are satisfied
that the speed is what you need for the job in hand: the higher the number
shown on the dial, the faster the speed
Setting the depth of cut
• To lock the tool at a set depth of cut, loosen the Cutting Depth Adjustment
Knob (13) and plunge the Motor Housing (12). Fasten the Depth Adjustment
Knob to hold the tool in this position
IMPORTANT: It is more dangerous to start the tool with the cutter already exposed
below the Low Friction Base (1) and requires extra care in use.
150W Tri-Function Multi-Tool
Making a cut
1. ALWAYS hold the tool using both hands on the handles provided. Ensure the
workpiece will not move. Use clamps wherever possible
2. Allow the motor to reach its full operating speed
3. Lower the cutter into the workpiece to the desired cutting depth
4. Move the tool slowly, keeping the Low Friction Base (1) held flat against the
workpiece
5. If edge cutting, the cutting of the workpiece should be on the left side relative
to the cutting direction. Keep the pressure constant and allow the cutter to
work steadily through the material. Be aware that knots and other variations
will slow the rate of progress
Cutting with the fence guide:
• Keep the Fence (23) pressed against the edge of the workpiece whilst making
a cut
• Maintain tool stability during cutting operations with the Fence by holding the
handle with one hand whilst securing the Fence with the other hand (Image B)
Note: Avoid 'bit chatter' by directing the cut anticlockwise for external cuts, and
clockwise for internal cuts.
Note: Moving the tool too fast can result in a poor quality finish and overloading of
the motor. Moving the tool too slowly can result in overheating the workpiece.
Note: Normal operation of the tool is to plunge the Motor Housing (12) after the
router has been switched on.
Accessories
• A range of accessories and consumables, including Silverstorm 750W Dust
Extractor and Safety Glasses is available from your SILVERLINE stockist. Spare
parts can be obtained from toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any
inspection, maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised SILVERLINE service centre. This
advice also applies to extension cords used with this tool
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves
when cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient,
a mild detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation
holes (where applicable)
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray
lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or
visible sparking
• If you suspect that the brushes may be worn, have them replaced at an
authorised SILVERLINE service centre
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
www.silverlinetools.com
7