Descargar Imprimir esta página

Ecco 3730 Serie Instrucciones De Instalacion Y Uso página 4

Publicidad

Idiomas disponibles

Idiomas disponibles

Notes on Synchronizing and Phase:
Phases A and B for each style of flash pattern in the table denote the relative timing between LED heads connected in a synchronizing
installation. To operate simultaneously, each LED must be set to the same phase (A + A or B + B); to operate alternately, LED heads
must be set to have the opposite phase (A + B or B + A).
To simplify the set-up of a synchronized installation, the following process is recommended:
1.
Determine the desired style of flash pattern for each LED head and set each unit individually (without the BLUE wires connected
together) to avoid confusion. It is also strongly recommended that the same style of flash pattern be used on all heads to produce
the most effective warning pattern.
2.
Connect the BLUE (SYNC) wires together and check that the LED heads are flashing in a synchronized manner as expected. If a
pattern on one module appears to be wrong, the YELLOW (PATTERN SET) wire can be used to cycle forward or backward on that
individual LED head until the correct pattern is selected. Note: This will only change the pattern in the one LED head and will not
affect the other units connected to the BLUE (SYNC) wire.
Synchronizing Example
As an example, an installation is required where there are two LED heads on the front driver side of the vehicle and two LED heads
on the front passenger side of the vehicle. The LED heads are to flash alternate sides of the vehicle with a synchronized quad-flash
style of flash pattern. First, configure the two LED heads for the driver side of the vehicle to pattern 4 (quad-flash style, phase A). Now
configure the other two LED heads for the passenger side with pattern 5 (quad-flash style, phase B). Connect the blue wires from the
four LED heads together. When power is switched to the LED heads, they should flash as expected (passenger side LED heads will
alternate with driver side LED heads). If necessary, corrections can be made to the flash patterns on each LED head individually with
the wiring complete.
Manufacturer Limited Warranty and Limitation of Liability:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer's specifications for this product (which are available from the
Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and workmanship. This Limited Warranty
extends for five (5) years from the date of purchase. Other warranties may apply, call Manufacturer for details. Manufacturer will, at its discretion, repair or
replace any product found by the Manufacturer to be defective and subject to this Limited Warranty.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICA-
TIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE
MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED
WARRANTY.
ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEALERS, AGENTS
OR OTHER MANUFACTURER'S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WARRANTY MAY NOT BE AMENDED,
MODIFIED, OR ENLARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICIAL OF MANUFACTURER WHICH EX-
PRESSLY REFERS TO THIS LIMITED WARRANTY.
Exclusion of Other Warranties: MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT.
BUYER'S SOLE AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING
THE PRODUCT AND ITS USE SHALL BE THE REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.
Limitation of Liability: IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RE-
LATED TO THE MANUFACTURER'S PRODUCTS, MANUFACTURER'S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID
FOR THE PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROF-
ITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL
DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF
MANUFACTURER OR A MANUFACTURER'S REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFAC-
TURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND
MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION
WITH SUCH PRODUCT.
This Limited Warranty defines specific legal rights. You may have other legal rights, which vary from state to state. Some states do not allow the exclusion
or limitation of incidental or consequential damages.
© 2007 ECCO
920-0064-00 Rev. B
833 West Diamond St
Boise, Idaho 83705
Customer Service
USA 800-635-5900
UK +44 (0)113 237 5340
AUS +61 (0)3 63322444
www.eccogroup.com
Page 4 of 4

Publicidad

loading

Productos relacionados para Ecco 3730 Serie

Este manual también es adecuado para:

A3730bktA3730tnkA3730dckA3730winA3730lic3730