Battery Pack Eps3I/Eps5 - Pulsar EPS3I Instrucciones

Battery type Li-Ion
Capacity (С), Ah
2.4
Rated voltage,V 11.1
Charged battery voltage, V 12.6
Discharged battery voltage, V 8.9
Full charge time, h 4
Full discharge time
(I=250 mА), h 9
Impedance, mΩ <100
Operating discharge current, А 0.2xC
Max. discharge current, А 0.5xC
500
Cycle life, at least
0 °C ... +45 °C / 32 °F ... +113 °F (RH 60±5%)
Charge temperature range
Operating temperature -20 °C ... +60 °C / -4 °F ... +140 °F (RH 60±5%)
Storage temperature +10 °C ... +22 °C /
Mains voltage range, V 110 ... 220
Degree of protection, IP code
(IEC60529) IPX5
Low battery indicator
yes
Mounting type Weaver
Dimensions,mm / inch
Length 85 / 3.3
Width 76 / 3
Height 40 / 1.6
0.23 / 8.1
Weight, kg / oz

Battery pack EPS3I/EPS5

Mains charger (110-220V)
Connector for devices with car lighter adapter
(2.1 mm DC socket)
Case*
User manual
Extension cable (1m)**
¼" tripod socket adapter**
* Supplied with EPS5
** Supplied with EPS3I
For improvement purposes, design of this
product is subject to change.
1
Li-Pol
5
11.1
12.6
8.9
4
20
<100
0.2xС
0.5xC
500
+50 °F ... +71°F
110 ... 220
n/a
no
n/a
106 / 4.2
75 / 2.9
20 / 0.8
0.35 / 12.3
Battery pack EPS5
Battery pack EPS3I
Rechargeable Li-Pol Battery Packs EPS3I
Pulsar and Yukon digital devices, thermal imagers, thermal and night vision
riflescopes. Battery Packs can be used with devices of the Digisight,
Digiforce, Quantum, Apex, Ranger series and other equipment outfitted with
an external power supply jack and Weaver rail or 1/4" socket.
The EPS3I has a capacity of 2.4Ah, is equipped with a mount to be affixed to a
Weaver rail of a device.
The EPS3I Battery Pack has a low battery indicator which allows you to
permanently control your battery status and avoid unexpected discharge.
The EPS5 features high capacity which significantly – up to 20 hours -
increases self-contained operation of external equipment. A 100 cm long cable
allows the battery packs to be stored in any suitable place, in a pocket, for
example. Thanks to the supplied connector for devices with car lighter
adapter, Battery Pack EPS5 is suitable to power various external devices like
GPS navigator, FM modulator, mini TV set, cell phone etc.
Precautions:
Do not expose to, dispose of the Battery Pack in fire.
The EPS3I is protected against directed water jets, the EPS5 – against
water spraying. However it is forbidden to submerge Battery Packs in
water.
Do not connect external equipment with a current consumption exceeding
fixed limit.
Battery packs are short circuit protected. However, situation which may
cause short circuit should be avoided.
Do not dismantle or deform the Battery Pack.
Keep out of reach of children.
Charging:
4
Only use the charger supplied with the Battery Pack. The use of
another charger may irreparably damage the Battery Pack or the
charger and may cause fire.
Never use a modified or damaged charger.
Charging current and voltage must comply with the parameters
outlined in the specifications table.
Charge the Battery Packs at a temperature ranging from 0 °C to +45 °C.
Do not leave the Battery Pack with a charger connected to the mains
longer than 24 hours after full charge.
Discharge:
Discharge current must not exceed 0.5xC. Exceeding current may cause
the Battery Pack to lose its capacity and to heat.
After a short-term over discharge subsequent charging will not
immediately damage the Battery pack. However long-term excessive
discharge may impact its performance and cause its capacity to reduce. If
the Battery pack was not used for a prolonged period of time, built-in
protection system will protect against excessive discharge.
and EPS5 are designed to power
3 2