Accessories (Fig .B) - Black and Decker DV4800N Manual De Usuario

Ocultar thumbs Ver también para DV4800N:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 31
ENGLISH
Insert the charger cord into the curved slot in the wall
u
mount bracket leaving approximately 8-9 inches excess.
Hang the appliance on the wall by placing the opening
u
on the base of the vac over the hooks in the wall mount
bracket.
Assembly

Accessories (fig .B)

These models may be supplied with some of the following
accessories:
A squeege tool (12) for wet use on hard surfaces.
u
(WD4810N, WD7210N and WD9610N Only)
A powered brush head (13) for vacuuming on cut pile
u
carpeting. The brush head is particularly useful for picking
up hair, threads, etc. (DV9610PN Only)
Fitting (Fig. D)
Insert the appropriate accessory into the front of the appli-
u
ance. Make sure that the accessory is pushed fully in.
Use
Before first use, the battery must be charged for at least
u
24 hours.
Place the appliance on the charging base whenever it is
u
not in use. (WD4810N, WD7210N and WD9610N Only)
Warning! Before charging, be sure to empty all liquid contents
and dry thoroughly, to avoid damage to your appliance.
Charging the battery (Fig. E & F)
Make sure that the appliance is switched off. The battery
u
will not be charged with the on/off switch in the on posi-
tion.
Plug the jack plug of the charger (6) into the charging
u
socket (4) of the appliance (Fig. E). (DV4800N and
DV9610PN Only)
Place the appliance on the charging base (7) (Fig. F).
u
(WD4810N, WD7210N and WD9610N Only)
Plug in the charger. Switch on at the mains. The charging
u
indicator (3) will be lit.
Leave the appliance to charge for at least 16 hours.
u
While charging, the charger may become warm. This is
normal and does not indicate a problem. The appliance can
be left connected to the charger indefinitely. The charging
indicator (3) will be lit as long as the appliance is connected to
the plugged-in charger.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
Switching on and off (fig. G)
To switch the appliance on, slide the on/off switch (1)
u
forward to position 1.
6
(Original instructions)
To switch the appliance off, slide the on/off switch (1) back
u
to position 0.
Dry pick up (DV4800N, DV9610PN)
For everyday spills of dry material.
u
Wet and dry pick up (WD4810N, WD7210N and
WD9610N Only)
For everyday spills of dry material, use your appliance
u
without the squeegee accessory.
Warning! Your product is designed for light spills only.
This appliance can also be used to pick up everyday liquid
u
spills. Use the squeegee accessory on non-absorbent,
hard surfaces. On absorbent surfaces, such as carpet,
your appliance will pick up wet spills better without the
accessory.
For best performance on hard surface wet pickups, insert
u
squeegee into the bowl nozzle opening.
For best results when using this accessory, hold the appli-
u
ance at an angle of 45° and pull it slowly towards you.
Do not fill the bowl beyond the end of the intake chute. If
u
there is any liquid in the bowl, do not turn the unit upside
down, sideways, point the nozzle upward, or shake the
vac excessively.
After picking up liquid substances clean the appliance and
u
filter immediately. Mold and mildew may form if the unit is
not properly cleaned after wet pickups.
Before charging, be sure to empty all liquid contents and
u
dry thoroughly, to avoid damage to your appliance.
Optimising the suction force
In order to keep the suction force optimised, the filters must be
cleared regularly during use.
Emptying and cleaning the product.
Removing the dust bowl and filters (fig. H, I, J & K).
Warning! The filters are re-usable and should be cleaned
regularly.
Press the release latch (2) and pull the dust bowl (5)
u
straight off.
While holding the dust bowl over a bin or sink, pull out the
u
filter to empty the contents of the bowl.
To replace the dust bowl, place it back onto the handle
u
until it "clicks" firmly into position.
Warning! Never use the appliance without the filters. Opti-
mum dust collection will only be achieved with clean filters.
Foam insert (fig. J) (WD4810N, WD7210N and
WD9610N)
Place the foam insert (10) into the centre of the wet/dry
u
deflector (11).

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dv9610pnWd4810nWd7210nWd9610n

Tabla de contenido