Confi Gur Ac Ión De Im Pr Es Or A; Des C R I Pc Ió N D E T Od As Co Nf I G Ur Ac I O Nes - HP DAILY JET HP1000 Manual De Operación

C o n f i g u r a c i o n e s d e l a i m p r e s o r a
8
De s c r ip c ión d e la s c o n fig u r a c io ne s
Use modo de configuraciones para modificar estos configuraciones.
Settings
FIRE
(FIRING MODE)
Configures "single" or
"continuous" printing.
PURGE PRINT
(PURGE PRINT)
Test the printhead.
ROTARY DIR.
(ROTARY DIR
‧
)
Set the operating
direction, LEFT-to-RIGHT
or RIGHT-to-LEFT.
DYNAMIC SN. LAST
(DYNAMIC SN﹒ LAST)
Serial Number Jump
(Backwards).
DYNAMIC SN. NEXT
(DYNAMIC SN﹒ NEXT)
Serial Number Jump
(Forwards).
ACTIVE NOZZLE
(ACTIVE NOZZLE Mode)
Set the printhead to only
use a group of nozzles.
DENSITY
(DENSITY Mode)
Set the printing density.
SPACE
(SPACE Mode)
Set the distance between
messages in continuous
print mode.
Description
Display: F (FIRING MODE), Press the confirmation key to modify this setting. Then
use the selection keys to switch between single and continuous printing modes ("N"
and "C"). Use the confirmation key to save this setting.
(Please see P.30 Set up the continuous printing)
Display: P (PURGE PRINT), Press the confirmation key to test the printhead. Then
print using the suggested motion. The printer should print "0123456789". To exit this
mode, press the function key to exit this mode.
(Please see P.39 Inkjet head printing test)
Display: R (ROTARY DIR.), Press the confirmation key to modify this setting. Then
use the selection keys to switch between left-to-right and right-to-left operating
mode ("L" and "R"). Press the confirmation key to save this setting.
L (Left to Right Mode).
R (Right to Left Mode).
(Please see P.31 Set up the printing direction)
Display: L (Mode DYNAMIC SN. LAST), Press the confirmation key to enable
backwards serial number jumping. Use the selection key to select a number
between 0-9. The printer will jump back the specified number of serials and continue
printing as normal. Press the confirmation key and this setting will be saved.
Continue printing as normal and the printer will jump back the correct number of
serials.
***This setting is only for use in conjunction with a serial number print messages.
(Please see P.32 Configuring Dynamic Serial Number)
Display: N (Mode DYNAMIC SN. NEXT), Press the confirmation key to enable
backwards serial number jumping. Use the selection key to select a number betwee
0-9. The printer will jump forwards the specified number of serials and continue
printing as normal. Press the confirmation key and this setting will be saved.
Continue printing as normal and the printer will jump forward the correct number of
serials.
***This setting is only for use in conjunction with a serial number print messages.
(Please see P.32 Configuring Dynamic Serial Number)
Display: H (ACTIVE NOZZLE Mode), Press the confirmation key to modify this
setting. Then use the selection keys switch between using all nozzles("B"), just even
nozzles("E"), or just odd nozzles("O").
(Please see P.33 Set up the printing nozzle)
Display: D (DENSITY Mode), Press the confirmation key to modify this setting. Then
use the selection keys to switch between the various density options. If ACTIVE
NOZZLE is set to "B" the two options are normal ("1") and darker ("2"). If ACTIVE
NOZZLE is set to "E" or "O" the four options are normal ("1") and increasing shades
of darkness ("2", "3", "4").
(Please see P.34 Set up the print density)
Display: S (SPACE Mode), Press the confirmation key to modify this setting. Then
use the selection keys to switch between head ("SPACE HEAD") and tail ("SPACE
TAIL"). Then use the selection keys to pick the distance between messages in
continuous mode in (0-9cm).
***This mode is only used in conjunction with CONTIUNOUS printing mode.
(Please see P.35 Configuring SPACE Mode)
n
29