Function Modes - Cardin Elettronica 24Vdc Motors 200 Manual Del Usuario

REMOTE CONTROL (fig. 12 - page 8)
The system can be remotely activated using radio control devices; to set the two
functions to channels A-B-C-D
A
B
position 2.
open-close
Memory module (MM)
This is extractable, furnished with a non volatile EEPROM type memory and contains
the transmitter codes and allows you to memorise up to 300 codes. The programmed
codes are maintained in this module even during blackouts.
Before memorising the transmitters for the first time remember to cancel
the entire memory content.
If the electronic card has to be replaced due to failure, the module can
be extracted from it and inserted into the new card. Make sure that the
module is correctly inserted as shown on page 8.
Signal LED "L4" (pag. 8):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER CODE MANAGEMENT
Memorising a channel (pag. 8):
P2 MEMO
2. At the same time activate the transmitter which is to be memorised.
P2 MEMO
4. Release the MEMO button: The LED will continue to flash.
5. Activate the transmitter again (same transmitter, same channel; if the channel is
different or it is a different transmitter the memorisation attempt will abort without
success).
L4
the transmitter has been correctly memorised.
Notes: It is not possible to memorise a code which is already in memory: if you
attempt this, the LED will switch off when you activate the transmitter (point 2). Only
P2 MEMO will you be able to continue the memorising
procedure.
If after activating the transmitter for the first time you wait for more than fifteen sec-
onds without activating the transmitter a second time the memorisation attempt will
abort without success.
Cancelling a channel (pag. 8):
2. Activate the transmitter channel that is to be cancelled.
3. The LED will remain lit for 2 seconds, indicating that the transmitter has been
cancelled.
Notes: If the user that you wish to cancel is not in memory, the LED will stop flash-
P3
procedure.
For both the memorisation and cancellation procedures, if the button is released
before activating the transmitter the procedure will abort.
Cancelling all user codes from memory (pag. 8):
L4
L4
Note: When the memory is almost full the time required to search for a user code
could take up to 1 second from when the command was received. If LED "L4" remains
lit memory is completely full. To memorise a new transmitter you will first have to
cancel a code from memory.
J4
SEQUENTIAL COMMAND;
CH2 (binding posts 9, 10
1 open-block-close-block
L4
L4
P3 DEL L4
P2+P3
Memorising ulterior channels via radio
J3
been memorised in the receiver, press the button in the transmitter as shown in
J5
figure.
Note: all the receivers within range when the channel button is pressed (and which
have at least one of the transmitter channel buttons memorised) will activate their
B1
3. Press one of the channel buttons on the same
transmitter. The receivers which do not contain
that channel code will sound a five-second long
which contain the channel code will sound
programming via radio" mode.
4. Press the previously chosen channel buttons on the transmitter which you wish
the receiver will be ready to receive another code.
5. To leave the programming mode wait for 3 seconds without pressing any buttons.
ming mode.
Note:
the memory is full.
CONNECTING THE ANTENNA
Connect an ANS400 tuned antenna using a coaxial cable RG58 (impedance 50Ω)
with a maximum length of 15 m.

FUNCTION MODES

1) Automatic
is completely closed the opening command will start a complete cycle which will
end with automatic reclosing.
Automatic reclosing starts after the programmed pause period has elapsed when
the opening cycle has been completed or straight away after the intervention of a
photoelectric cell (the intervention of a photoelectric cell causes the pause time to
be reset).
During the pause time the symbol
blocking button during this period will stop automatic reclosing and consequently
stop the display from flashing.
The indicator light remains lit until the closing manoeuvre has terminated.
Note: the courtesy light switches on each time a movement command is given (both
via cable or via radio) and switches off 30 seconds after the manoeuvre has been
2) Semiautomatic
control using separate opening and closing commands. When the door has reached the
completely open position the system will wait until it receives a closing command either
via an external control button or via radio control, before completing the cycle.
The indicator light remains lit until the closing manoeuvre has terminated.
3) Manual manoeuvring with released motors
Releasing the motor the gate can be moved by hand; once the motor has been
reangaged the programmer does not control the position of the gate leaves and so
when the next movement command is given (after the motors have been blocked
again) repositioning will take place due to the positioning error.
Attention! If a command is given while the motor is released the
symbol
motor has been released.
22
J3
A, B, C or D
programming via radio
programming via radio
2
will flash on the display and pressing the
J5 1
2
or will appear on the display depending on which
-
ON
OFF