Residual Risks; Electrical Safety - Stanley SM16 Manual De Instrucciones

ENGLISH (
Original Instructions)
and chutes are properly adjusted.
♦ Please be aware of the following factors influencing
exposure to noise:
– use saw blades designed to reduce the emitted
noise;
– use only well sharpened saw blades;
♦ Machine maintenance shall be conducted periodically;
♦ Machine faults, including guards or saw blade, shall be
reported as soon as they are discovered;
♦ Provide adequate general or localized lighting;
♦ Ensure the operator is adequately trained in the use,
adjustment and operation of the machine;
♦ Ensure that any spacers and spindle rings are suitable
for the purpose as stated in this manual.
♦ Refrain from removing any cut-offs or other parts of
the workpiece from the cutting area while the machine
is running and the saw head is not in the rest position
♦ Never cut workpieces shorter than 30 mm(Figure 34).
♦ Without additional support the machine is designed to
accept the maximum workpiece size of:
– Height 75 mm by width 140 mm by length 460 mm
– Longer workpieces need to be supported by suit-
able additional table(work support). Always clamp
the workpiece safely.
♦ In case of an accident or machine failure, immediately
turn the machine off and disconnect machine from the
power source.
♦ Report the failure and mark the machine in suitable
form to prevent other people from using the defective
machine.
♦ When the saw blade is blocked due to abnormal feed
force during cutting, turn the machine off and discon-
nect it from power supply. Remove the workpiece and
ensure that the saw blade runs free. Turn the machine
on and start new cutting operation with reduced feed
force.
♦ Never cut light alloy, especially magnesium.
♦ Whenever the situation allows, mount the machine to
a bench using bolts.

RESIDUAL RISKS

The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety reg-
ulations and the implementation of safety devices,
certain residual risks cannot be avoided. These are:
– Impairment of hearing.
– Risk of accidents caused by the uncovered parts of the
rotating saw blade.
– Risk of injury when changing the blade.
– Risk of squeezing fingers when opening the guards.
– Health hazards caused by breathing dust developed
when sawing wood, especially oak, beech and MDF.
The following factors increase the risk of breathing
problems:
42
– No dust extractor connected when sawing wood.
– Insufficient dust extraction caused by uncleaned exhaust
filters.

ELECTRICAL SAFETY

Only one voltage is applicable to this tool. Be sure to check
that the power supply corresponds to the voltage on the
rating plate.
Your Stanley tool is equipped with double insula-
tion, hence, it does not require to be earthed
When the power cord is damaged, have it sent
to a STANLEY service center for replacement to specially
prepared cables.
USING AN EXTENSION CABLE
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool
(see Technical Data).The minimum conductor size is 1.5
mm ; the maximum length is 30 m. When using a cable
2
reel, always unwind the cable completely.
Cable cross-sectional
area (mm )
2
0.75
1.00
1.50
2.50
4.00
Voltage Amperes Cable rated current (Ampere)
110~127 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
LABELS ON TOOL
In addition to the pictographs used in this manual, the
labels on the tool show the following pictographs:
Cable rated current
(Ampere)
6
10
15
20
25
Cable length (m)
7.5 15 25 30 45
6 6 6 6 6
6 6 6 6 15
6 6 10 15 20
10 10 15 20 20
15 15 20 25 25
20 20 25 - -
6 6 6 6 6
6 6 6 6 6
6 6 6 6 10
10 10 10 10 15
15 15 15 15 20
20 20 20 20 25
60
10
15
20
25
-
-
6
6
15
15
20
-