Residual Risks; Assembly; Commissioning - Dexter power MS8 Traducción De Las Instrucciones Originales De Funcionamiento

of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Safety instructions for handling batteries
1 Always make sure that the batteries are inserted
with the correct polarity (+ and –), as indicated on
the battery.
2 Do not short-circuit batteries.
Do not charge non-rechargeable batteries.
3
4 Do not overcharge batteries!
5 Do not mix old and new batteries or batteries of
different types or manufacturers! Replace an entire
set of batteries at the same time.
Immediately remove used batteries from the device
6
and dispose of them properly!
7 Do not allow batteries to heat up!
Do not weld or solder directly on batteries!
8
9 Do not dismantle batteries!
10 Do not allow batteries to deform!
Do not throw batteries into fire!
11
12 Keep batteries out of the reach of children.
13 Do not allow children to replace batteries without
supervision!
14 Do not keep batteries near fire, ovens or other
sources of heat. Do not use batteries in direct sun-
light or store them in vehicles in hot weather.
15 Keep unused batteries in the original packaging and
keep them away from metal objects. Do not mix
unpacked batteries or toss them together! This can
lead to a short-circuit of the battery and thus dam-
age, burns or even the risk of fire.
16 Remove batteries from the equipment when it will
not be used for an extended period of time, unless
it is for emergencies!
17 NEVER handle batteries that have leaked without
appropriate protection. If the leaked fluid comes into
contact with your skin, the skin in this area should be
rinsed off under running water immediately. Always
prevent the fluid from coming into contact with the
eyes and mouth. In the event of contact, please seek
immediate medical attention.
18 Clean the battery contacts and corresponding con-
tacts in the device prior to inserting the batteries.
m Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instruc-
tions" and the „Proper use" are observed along with
the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the machine
16 GB
in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your mitre saw provides optimal perfor-
mance.
• Hands may never enter the processing zone when the
machine is in operation.
• Release the handle button and switch off the machine
prior to any operations.
m Assembly
WARNING! For you own safety, only insert the mains
plug in an outlet when all assembly steps have been
completed and you have read and understood the
safety and operating instructions.
Lift the saw out of the packaging and place it on your
work bench. (Positioning of the saw on the work bench
- see the next page under „POSITIONING / WORK STA-
TION")
Installation of the dust bag
• Squeeze together the metal ring on the dust bag (12)
and attach it to the outlet opening in the motor area.
Assembling the work piece clamping device (fig. 1.1)
• Loosen the locking screw (17) and attach the work
piece clamping device (10) to the left or right of the
fixed saw bench.
• Afterwards, retighten the locking screws (17).
Assembling the work piece supports (fig. 1.1 – 1.2)
• Loosen the cross-head screw (14) and guide the work
piece support through the specified hole on the side
of the fixed saw bench.
• Make sure that the work piece support (15) is also
guided through the two plates (19) on the underneath.
• Afterwards, retighten the cross-head screw (14).
• Repeat this process on the other side.
Assembling the support stand (fig. 1.1 – 1.2)
• Loosen the cross-head screws (18) on the underneath
of the saw and guide the support stand (16) through
the specified holes on the back of the saw.
• Afterwards, retighten the cross-head screws (18).

Commissioning

Prior to commissioning, observe the safety instruc-
tions in the operating instructions.
REMOVAL FROM THE PACKAGING
Remove the machine from its package, which protects it
during transport, without damaging the package in order
to be able to use it later for transporting the mitre saw for
long-term storage.