GHP Group Dyna-Glo Delux RA100NGDGD Manual De Instrucciones De Operación Y Lista De Partes página 3

Dyna-Glo Delux Operating Instructions and Parts Manual
Models R 100NGDGD and R 250NGDGD
General Safety Information
(Continued)
– Check heater for damage before each
use. Do not use damaged heater.
Minimum heater clearance from
combustibles:
Sides: 6 feet Top: 5 feet
Floor: Combustible - Not for use
on finished floors
– The heater, other than a heater with
integral propane gas container, must
be located at least 6 feet (in Canada,
distance must be 10 feet) from any
propane gas container.
– Blower or radiant type heaters shall
not be directed toward any propane
gas container within 20 feet (6 m).
– Check hose before each use of heater.
Do not use if hose is cut or damaged.
Replace with hose specified by
manufacturer.
– lways be sure to place the heater on
a stable and level surface while the
heater is in operation.
– The heater is not intended for use on
finished floors. Warping or other
damage may occur.
– Place heater away from any breezes or
drafts. Keep away from dripping
water or rain.
– Keep small children and animals away
from the heater.
– Never handle, move or service a hot or
operating heater. Wait 20 minutes after
turning heater off before touching the
heater. Severe burns can result.
– lways wear gloves when handling
the heater to prevent injury.
– Never attach ductwork to heater.
– Do not alter heater. Keep heater in its
original state.
For Technical Support or Troubleshooting, Call: 1-877-477-4768, 8:00 am - 5:00 pm CST
– Do not use heater if altered.
– Turn off gas supply to heater when
not in use.
– Use only original replacement parts.
This heater must use design specific
parts. Do not substitute or use generic
parts. Improper replacement parts
could cause serious or fatal injury.
ssembly
MODEL R 100NGDGD
1. Provide natural gas supply system.
2. Install plumbing to a low pressure
natural gas source to heater. The
source must be regulated to 1/2 PSI,
maximum 3/4 inch I.D. pipe or flexible
connector, not longer than 10 feet.
3. Be sure to use thread sealing
compound when connecting the hose
to the heater at the 1/2 NPT fitting at
the regulator inlet. Tighten all fittings
with a wrench.
4. Open natural gas supply valve
SLOWLY.
5. Check all connections for leaks.
Figure 2 – Pipe and Valve Inlet
Never use an open
flame to check for a
leak. pply 50/50 mixture of liquid soap
and water to all joints. Bubbles forming
show a leak. Correct all leaks at once.
6. Close natural gas supply valve.
3
Figure 3 – Heater Control Knob –
R 100NGDGD
MODEL R 250NGDGD
1. Provide natural gas supply system.
2. Install plumbing to a low pressure
natural gas source to heater.
3. Connect gas supply to heater using
minimum 3/8" ID pipe. Maximum
pipe length is 10 feet.
4. Connect hose or plumbing to 1/2"
NPT flare fitting at the valve inlet.
Tighten all fittings with a wrench.
5. Open natural gas supply valve
SLOWLY. Check all connections for
leaks. Never use an open flame to
check for leaks.
6. Close natural gas supply valve.
NOTE: Keep hands and face away from
outlet (around top of shelf) of heater
while attempting to start heater.
www.ghpgroupinc.com
PROFESSIONAL GRADE
E
N
G
L
I
S
H