Publicidad
PREPARATION TIPS
• Begin by measuring the width of the back wall, after it has been cleaned and
prepared for installation. If this measurement exceeds the width of the JETCOAT™
Shower Wall System back panels that came with your kit, you will need to purchase a
larger kit or additional wall panels.
• Then, measure the height of the back and side walls above the bathtub
or shower base. If the height of the walls is less than the height of the
JETCOAT™ panels, they can be easily cut to fit.
• Turn off the water supply.
• Remove all shower hardware and decorations, including but not limited
to: faucet handles, escutcheons, filler spouts, towel bars, and soap dishes.
• Measure the location of the plumbing cutouts, as stated in the
instructions. To be sure your measurements are correct, make
a cardboard template to test the plumbing cutouts prior cutting the
JETCOAT™ panels.
• All plumbing and electrical work inside the walls must be finished prior to
installing the wall panels.
• Before you being, trial fit the side panels. The unfinished back side of the
panel should be place against the sub-wall.
• Walls should be solid, plumb, and square within 1/8 inch of true. The
JETCOAT™ Shower Wall System has been designed to allow for trimming,
to accommodate minor alignment problems.
• The mounting surface should be cleaned and prepared, according to the
Installation Procedure.
• If you plan to install a recessed accessory, cut the panel accordingly
after it has been fully installed, and had the proper time to adhere to
the wall. Remember to be considerate of wall studs when
positioning the accessory.
CAULKING TIPS
• Follow the instructions on the tube of your chosen caulk.
• Once you have completed the project, inspect all of the areas that have
been caulked for gaps. Fill in the areas as needed.
• Remove any excess caulk using denatured alcohol and a clean cloth. Use
caution, and do not to disturb any of the caulk joints.
INSTALLATION PROCEDURE
The JETCOAT
Shower Wall system can be installed over a variety of products. Consult
™
with a professional contractor if you intend to apply the panels to any surface than those
described.
CEMENT/CONCRETE:
• Additional silicone may be required to properly secure the substrate and
the wall panel, depending on the condition (flatness) of the existing wall.
• The complete area must be sealed with two coats of water or oil-based
sealer, to ensure proper adhesion of the Jetcoat™ Shower Wall System.
• Complete the installation of the wall panels following the instruction
manual, after the sealer has completely dried.
MASONITE:
• Surface must be completely clean. This includes but not limited too: soap
scum, free of any dust, and any other contaminates.
• Complete the installation of the wall panels following the instruction
manual, after the sealer has completely dried.
OLD TILE:
IMPORTANT: All plastic tiles must be removed. Old ceramic tiles do not need to be
removed, if solidly adhered.
• Additional silicone may be required to properly secure the substrate and
the wall panel, depending on the condition of the existing wall.
• Properly remove and or reattach any loose ceramic tiles.
• Remove all tile accessories attached to the wall.
• Complete the shower wall installation by following the instruction manual.
PLASTER:
• Additional silicone may be required to properly secure the substrate and
the wall panel, depending on the condition of the existing wall.
• Smooth all textured and/or swirled finishes by sanding.
• Surface must be completely clean. This includes but not limited too: soap
scum, free of any dust, and any other contaminates.
• Complete the installation of the wall panels following the instruction
manual, after the sealer has completely dried.
SHEETROCK/GREENBOARD/CEMENT BOARD/ WOOD:
• Surface must be completely clean. This includes but not limited too: soap
scum, free of any dust, and any other contaminates.
• Complete the installation of the wall panels following the instruction
manual, after the sealer has completely dried.
WALLPAPER:
• Properly remove all wallpaper from the area being covered. Surface must
be completely clean. This includes but not limited too: soap scum, free of
any dust, and any other contaminates.
• Complete the installation of the wall panels following the instruction
manual, after the sealer has completely dried.
LIMITED WARRANTY
Foremost Groups, Inc. and Foremost International, Ltd., warrants to the original
purchaser that this JETCOAT™ Shower Wall System kit will be free of manufacturing
defects, which affect its performance as a bathing or showering fixture, under the
following conditions and subject to the limitations contained in the "Remedies" and
"Warranty Limitations" sections.
Please go here to register:
USA: http://www.foremostbath.com/page/warranty
CANADA: https://foremostcanada.com/warranty-registration/
The Limited Warranty applies for 10 years from the date of purchase if the fixture is used
in a residential owner-occupied building for non-commercial purposes; or for 2 years
from the date of purchase if it is used in any other building, including any building used
for rental, commercial, or business purposes.
• This Limited Warranty is void if the fixture is not installed in accordance
with the installation instructions supplied by Foremost, or local building
codes and ordinances, or if the care and cleaning instructions supplied by
Foremost are not followed.
• This Limited Warranty is also void if the fixture is moved from the location
of its initial installation, or is subjected to accident, abuse, or misuse.
• The Limited Warranty excludes normal wear and tear, and does not
cover damage that can be repaired by following the
Scratch Removal Instructions.
• This Limited Warranty shall be void unless any failure or non-conformance
is discovered before the expiration of this warranty, and is reported
to Foremost Groups, Inc. or Foremost International, Ltd. in writing, accompanied by
the original proof purchase, within 30 days of discovery.
REMEDIES:
The original purchaser's remedy under this Limited Warranty is limited to the repair,
replacement, or refund of the purchase price of the fixture, at Foremost's sole option,
of any part of the fixture which has failed or does not conform to the manufacturer's
specifications.
In no event shall Foremost be liable for lost profits, loss of use, incidental, special or
consequential damages including, but not limited to, damage to or loss of use of the
building or its contents, arising out of any defect in the fixture; nor shall Foremost be
liable for any amount in excess of the original purchase price of the fixture.
Foremost reserves the right to require the return, at purchaser's expense, of the
damaged fixture for repair or exchange before providing services under this Limited
Warranty. If Foremost elects to replace the fixture, its obligation is limited to supplying a
replacement unit or component part of comparable size and style, and does not include
the cost of removal, installation, or transportation, which must be borne by the purchaser.
Replacement parts provided under this Limited Warranty are warranted for the
remainder of the original warranty period applicable to the fixture, as if such parts were
original components of that fixture.
WARRANTY LIMITATIONS:
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE
FACE HEREOF. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. FOREMOST
DISCLAIMS ANY AND ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states or provinces do not allow limitations of incidental or
consequential damages, so the above limitations and exclusions may not apply to you.
In such states or provinces, Foremost's liability shall be limited to the extent permitted
by state or provincial law. ANY IMPLIED WARRANTIES ARISING BY WAY OF STATE OR
PROVINCIAL LAW, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION AND IN SCOPE OF COVERAGE TO THE TERMS OF THIS LIMITED
WARRANTY, UNLESS A SHORTER PERIOD IS ALLOWED BY LAW.
Publicidad
