Remington MB320C Manual De Usuario página 4

ENGLISH
Your beard trimmer cannot be overcharged. However, if the product is not going to be used
for an extended period time (2-3 months), unplug it from the mains and store. Fully recharge
your beard trimmer when you would like to use it again.
To preserve the life of your batteries, let them run out every six months then recharge for
14-16 hours.
CORDED USE
Connect the charging adaptor to the product and then to the mains.
CAUTION: Extended mains only use will result in the reduction of the battery life.
HOW TO USE
BEFORE YOU BEGIN
Always comb your beard or moustache with a fi ne comb before you start trimming.
Adjusting the Trim Length
The trimmer comb can be adjusted to give you 9 different trim lengths simply by turning the
zoom wheel to the desired setting. Turn the zoom wheel clockwise for shorter length, anti-
clockwise for longer length. The wheel will click into place as it reaches each setting, and the
setting number will appear on the length position indicator.
SETTING HAIR DESCRIPTION
1 Stubble or cropped look
2
3 Short
4
5 Medium
6
7
8
9 Long
2
061175_REM_IFU_MB320C.indd 2-3 061175_REM_IFU_MB320C.indd 2-3
Note Trimmer comb must be attached to the groomer in order to use the hair length
selector.
TO THIN AND TAPER THE BEARD/MOUSTACHE
Use the zoom wheel to set the trimmer comb to the desired length setting. The setting
will appear on the length position indicator. If you are trimming for the fi rst time start
with the maximum trimming length setting (9).
Turn the unit on.
Place the fl at top of the trimmer comb against the skin (DIAGRAM A)
Slowly slide the trimmer through the hair. Repeat from different directions as necessary.
If hair builds up in the trimmer comb during the trimming process, switch the unit off, pull
off the comb and brush/rinse off (DIAGRAM B)
TO DEFINE THE BEARD/MOUSTACHE LINE
Remove the trimmer comb attachment (DIAGRAM B)
Start with edge of beard/moustache line and gently lower the trimmer blade onto your
skin (DIAGRAM C). Use motions towards edge of beard/moustache line to trim to
desired locations in facial area and away from beard in neck area.
For fi ner shaping, raise the pop-up trimmer. Shape as desired.
TRIMMING EDGE OF SIDEBURNS
Remove the trimmer comb attachment (DIAGRAM B)
Start with edge of sideburn, and with the trimmer blades resting lightly against your skin,
use motions towards edge of sideburn line to trim to desired locations in facial area.
For fi ner shaping, raise the pop-up trimmer. Shape as desired.
HAIR LENGTH
TRIMMING THE NAPE OF YOUR NECK
1,5 mm 0.06" Note: You will need a hand mirror for this operation if performing it alone.
Remove the trimmer comb attachment (DIAGRAM B)
2,5 mm 0.1"
Use your fi ngers to lift the hair at the base of your head up off the neck. Your index fi nger
should be covering the roots of the hairs you are lifting to prevent accidental removal by
4 mm 0.16"
trimmer.
With your other hand, use the trimmer as shown in (DIAGRAM D)
5,5 mm 0.22"
Using your other hand, hold the trimmer to the base of your neck with the cutting unit
facing up, and move the trimmer up the length of the neck until it touches your fi nger
7 mm 0.28"
covering the hair roots at the base of your head. Be sure to move the unit slowly when
9 mm 0.35"
performing this operation and to keep the hair roots at the base of your head out of the
way of the trimmer.
11 mm 0.43"
REMOVING THE TRIMMER COMB ATTACHMENT AND
14 mm 0.55"
CUTTING ASSEMBLY
Hold the trimmer in one hand with your thumb fi rmly on the zoom wheel to keep it from
18 mm 0.71"
turning.
With your other hand, gently pull the trimmer comb attachment off the trimmer.
Remove the cutting assembly by fi rmly pushing up on the blade with your thumb.
(DIAGRAM E)
3
21.11.2006 16:52:25 Uhr 21.11.2006 16:52:25 Uhr