Weed Eater WE12B Manual De Instrucciones página 8

a shoulder strap (optional accessory part number
579178201) may be used with your unit. Attach the strap
to the unit before operation. Attach the hook onto the
retainer.
HOW TO CONVERT UNIT FROM VACUUM USE
TO BLOWER USE
a WARNING: Stop the unit and disconnect from the
power source before opening the inlet cover or
attempting to install or remove the blower tube or
vacuum tubes. The motor must be stopped and
the impeller blades no longer turning to avoid
serious injury from the rotating blades.
1. Stop unit and unplug the extension cord.
2. Remove the elbow tube and collection bag.
BEFORE STARTING
• Make sure you have the proper personal protective
equipment.
• Inspect the cleanliness of the power tool. Make sure the
handles are dry, clean, and free of oil and grease.
• Inspect for broken or damaged parts. Do not use the
power tool if any damage affects safety or operation.
Have damage repaired by an authorized service center.
• Inspect the power cord. If it is damaged, have it repaired
by an authorized service center.
• Inspect the extension cord. Replace it if it is damaged.
• Connect the power cord to the extension cord.
• Connect the extension cord to the power supply.
Keep the extension cord clear of the work area. Position
the cord so that it will not get caught on bushes, hedges,
tree trunks or other obstructions while you are working.
a WARNING: The use of eye protection is
recommended.
a WARNING: Check the extension cord before each
use and frequently while working. If damaged,
replace immediately. Never use the tool with a
damaged cord since touching the damaged area
could cause electrical shock, resulting in serious
injury.
a WARNING: Unplug the power tool from the power
source before making adjustments.
STARTING AND STOPPING THE TOOL
Move the ON/OFF switch to the ON (I) position to turn on
the tool.
Move the ON/OFF switch to the OFF (0) position to turn
off the tool.
a WARNING: Unplug the power tool from the power
source before performing maintenance. Severe
injury or death could occur from electrical shock
or body contact with moving parts.
After you have finished using the tool:
8
3. Remove the vacuum tubes by releasing the latch on
the vacuum inlet cover and rotating the cover until the
tubes are released from the latches of the retaining
posts.
4. Close the inlet cover and make sure it is latched
closed.
5. Re-install the blower tube. Refer to ATTACHING THE
BLOWER TUBE for instructions on how to attach this
item.
CORD RESTRAINT (D)
1. Make a loop in the extension cord and push the loop
through the slot in the handle.
2. Position the loop over the hook and pull the cord back
through the slot.
OPERATION
USING YOUR UNIT AS A BLOWER (E)
a WARNING: Inspect the area before using the
unit. Remove all debris and hard objects such
as rocks, glass, wire, etc., that can ricochet, be
thrown, or otherwise cause injury or damage
during operation.
Use the tool as a blower for:
• Sweeping debris or grass clippings from driveways,
sidewalks, patios, etc.
• Blowing grass clippings, straw, or leaves into piles,
or removing debris from corners, around joints, or
between bricks.
Direct air flow by directing the blower tube down or to one
side. Always work away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and moving outward.
This will help prevent an accumulation of debris which
could fly into your face.
Be careful when working near plants. The force of the air
could damage tender plants.
USING YOUR UNIT AS A VACUUM (F)
a WARNING: Do not vacuum stones, gravel, metal,
broken glass, rubber mulch, etc., to avoid severe
damage to the impeller. To avoid the possibility of
electrical shock, do not attempt to vacuum water
or other liquids.
Use the tool as a vacuum for picking up dry material such
as leaves, grass, small twigs, and bits of paper.
For best results during vacuum use, operate your unit at
high speed.
Move slowly back and forth over the material as you
vacuum. Avoid forcing the unit into a pile of debris as this
can clog the unit.
Keep the vacuum tube about an inch above the ground for
best results.
a WARNING: If the unit becomes clogged, stop the
unit and unplug the extension cord.Wait until the
impeller has completely stopped turning, then
remove the vacuum tubes. Carefully reach into
the vacuum opening and clear out the clogged
debris.
MAINTENANCE
1. Disconnect from the outlet.
2. Remove debris from the tool with a soft brush or dry
cloth. Never clean the tool with water, cleaning fluids,
or solvents.
3. Use a soft brush to remove debris from the air vents.