Shark V15Z Manual Del Propietário página 7

INSTRUCCIONES PARA OPERAR
ADVERTENCIA:
Siempre
desenchufar del tomacorriente antes de
abrir el compartimiento del colector de
polvo.
Nota
: Siempre que se opere la
aspiradora debe tener instalado el filtro
HEPA.
Uso como Aspiradora de Mano
1. Insertar el conector de la manguera
para escobilla de polvo en la salida
de la cámara de la escobilla
motorizada. Asegurar la manguera
en el soporte para manguera. (Fig. 1)
Fig. 1
Aspirado con Manguera
Para usar la aspiradora sólo con
manguera y la escobilla para polvo o
la boquilla para rendijas:
1. Girar la tapa de la cámara de la
escobilla motorizada presionando
el botón de seguro hasta que
enganche en posición.
2. Sacar la manguera flexible de la
salida de la cámara de la
escobilla y desenganchar la
manguera de su soporte. (Fig. 3)
Fig. 2
Fig. 3
3. Para usar la manguera flexible con
la escobilla para polvo, sostener la
manguera en una mano y con la
otra mano tirar de la escobilla para
polvo girándola en el contra sentido
del reloj hasta que salga y
enganche en posición. (Fig. 4)
Fig. 4
4. Para usar la manguera flexible con
la boquilla para rendijas, cerciorarse
que la manguera esté en posición
de guardada e insertar la boquilla
para rendijas, en la boca de la
manguera. (Fig. 5)
Fig. 5
CUIDADO
: La aspiradora de mano es
muy potente. Asegurarse de sostenerla
firmemente, de lo contrario podría
escaparse de la mano y causar
lesiones.
13
OPERATING INSTRUCTIONS
6. Vigorously "TapClean"
the HEPA Dust Cup
Filter on a hard
surface until no more
dust is observed
falling out from
between the pleats of
the filter. (Fig. 11)
Fig. 11
7. "TapClean" the Debris
Screen or rinse under
a faucet until clean.
(Fig. 12) Remember
that the Debris Screen
must be completely
dry before reinstalling
in the vacuum.
8. Replace the Debris Screen on the
HEPA Dust Cup Filter and reinstall
filter assembly in the vacuum. (not
shown)
PLEASE NOTE: The white pleated
filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the
performance of the filter. If the HEPA
Dust Cup Filter
Fig. A
is properly
"TapCleaned"
after each use
Wash once a
and suction
month or when
suction
does not return
appears
to 100%, then
reduced.
.
we suggest that
Warning:
Allow 24
the HEPA filter
hours for drying before
be "TapCleaned"
replacing in unit.
vigorously until no
more dust can be removed, then
rinsed under the faucet and allowed to
dry for 24 hours before refitting into
the vacuum. (Fig. A) This should be
done once a month or when
suction appears reduced.
CAUTION
: The suction hole must be
open and free of any obstructions at
all times. Otherwise, the motor will
overheat and could become
damaged.
Motor Thermostat
IMPORTANT:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)
• If clogged hose or filter is found,
unclog the hose and replace the
Fig. 12
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
Debris • After unit has cooled down for
Screen
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
Motor Thermostat
IMPORTANT:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the power
source.
• Check the source of overheating
problem. (i.e. clogged hose or filter)
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for 45
minutes, plug in the cleaner and
push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1 (800) 798-7398.
6