Preventive Maintenance - Carlisle Binks 183GZ-5200 Manual De Servicio

EN
BACK FLUSHING EXCESS
MATERIAL
When spraying is complete, back flush
remaining material in spray gun and hose as
follows:
1. Turn off air to material tank and bleed air
out of the material tank.
2. Loosen clamps on tank lid. Tip lid so
material will run out of fluid tube into
material tank.
3. Loosen air cap on gun 2 to 3 turns and
hold rag over cap. Pull trigger and force
material from gun and hose back into
tank.
TO CLEAN HOSE AND GUN
PASSAGES:
1. Fill Hose/Gun Cleaner with suitable
cleaning solvent. Note: This model cannot
be used with halogenated hydrocarbon
solvents. Close lid on cleaner.
2. Connect air hose to ¼ NPS(M) ball valve
(4). Close ball valve. Regulate air pressure
(must be remotely regulated) to a
maximum of 110 PSI.
3. Disconnect material hose from material
supply tank and connect to 3/8 NPS(M)
ball valve (5).
5
6
9
www.carlisleft.com
4. Open both ball valves.
5. Turn metering valve on top of the Hose/
Gun Cleaner to adjust the solvent-to-air
ratio. Turn counterclockwise to increase
solvent and clockwise to decrease solvent.
Fully clockwise shuts off solvent
completely. To begin, open
counterclockwise 2 turns for sufficient
solvent for cleaning.
6. Trigger gun into a properly grounded
container. Continue spraying until solvent
is clear with no traces of paint.
7. Turn metering valve full clockwise,
shutting off solvent flow, while allowing air
to continue to flow. Continue until all
solvent is removed.
8. Turn off air at source. Trigger gun to
remove residual air pressure. Close both
ball valves.

PREVENTIVE MAINTENANCE

Check Lid Gasket (11) and Needle Valve
Gasket (2) for signs of wear or damage.
Replace as needed.
Lift ring on safety valve (6) once a week to
unseat it and make sure that it is working
properly. Safety valve should be kept clean
and free of dirt ad paint at all times.
1
2
4
3
7
8
10
11
ITEM
NO.
1
2
12
3
13
4
5
6
7
8 • -----
9 • -----
14
10
11
12
13
15
14
15
• Purchase locally
PART NO. DESCRIPTION
HD-409 NEEDLE VALVE ASSEMBLY
HD-39-K2 NEEDLE VALVE GASKET (KIT 0F 2)
HD-430 HD SUB ASSEMBLY
VA-542 BALL VALVE (1/4 NPS)
VA-540 BALL VALVE (3/8 NPS)
TIA-5110 SAFETY VALVE ASSEMBLY
SSG-8184-K2 O-RING (KIT OF 2)
PLUG (1/2-14 NPT)
PLUG (3/8-18 NPT)
QMG-400 TANK LID
QMS-80-1 TANK GASKET
PT-31 FLUID TUBE
PT-78-K10 TANK LINER (KIT OF 10)
KK-5013 CLAMP, PIN, & SCREW KIT
QMG-502-1 TANK & LUG ASSEMBLY
4 / 6
ACCESSORIES
Air Supply Hose
71-20000 Air Hose – with static ground wire
braid, 5/16" ID. Also need two re-useable
72-1317 connectors.
Or
71-2100 Air Hose – with static ground wire
braid, 3/8" ID. Also need two re-useable
72-1325 connectors.
Or
Fluid Delivery Hose
71-282 Nylon lined fluid hose – 3/8" ID. Also
need two re-useable 72-1328 connectors.
GROUNDING DIAGRAM
Purchase hardware locally
5/16–18 Hex Head
Nut (2 Required)
5/16–18 x 3/4 Long
Hex Head Bolt
(1 Required)
Sufficient Length
12 Gauge Wire
(Not Shown)
2X
5/16 Lock Washer
(1 Required)
Tank Skirt (Ref)
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
77-2933-R1.0 (6/2017)