Tabla de contenido
Publicidad
MANUALS FOR OTHER UNITS CAN BE FOUND AT WWW.SOURCEONEOPE.COM
PLUGR PL855 PRO HD 30" TURF AERATOR MANUAL
OPERATING INSTRUCTIONS
NO ASSEMBLY REQUIRED
Hydrostat: The hydrostat has been serviced at the factory
and is ready to operate. The lever in front of the machine
marked Hydrostat Bypass needs to be down for hydrostat to
run.
Engine: Engine and gear case are factory filled with high
quality detergent SAE 30 oil, (SE, SF or SG). Check lever prior
to operation. Please refer to the engine manual or call the
engine manufacturer at the phone number listed in the
engine instructions if there are any questions regarding the
engine. NOTE: GASOLINE CAN BE HAZARDOUS. HANDLE
GASOLINE CAREFULLY AT ALL TIMES! USE LEAD FREE
GASOLINE WITHOUT OIL MIXED IN. All Plugr aerators will run
on E-10 blended (10%) ethanol.
CAUTION! KEEP FINGERS FROM BEING PINCHED UNDER
THE MOVING HAND LEVERS DURING ENGAGEMENT.
Lever operation: Bottom left lever engages forward motion.
Bottom right lever engages tines.
Center lever: This lever swings the plugr mechanism
forward into the operating position. Release handle and allow
lever to move forward. It will automatically pull itself into
operating position.
To aerate: Pull bottom left lever first to engage forward
motion. Pull up bottom right lever to engage tines.
To stop PLUGR: Release bottom right lever first, then release
bottom left lever. SHUT OFF ENGINE if not continuing.
Transport mode: Pull center lever up. Leave bottom right
lever down. Engage bottom left lever only.
To reverse: Make sure tines are in the up position and
gently push down on left lever.
To remove access cover: Remove rubber latches from both
sides of top cover, lift front of cover and slide back gently. To
remove front cover, slide towards front of machine slightly
and lift straight up.
To operate in cold temperatures: Engage tines in "up"
position for at least two minutes prior to actual aeration to
warm cam grease.
THESE INSTRUCTIONS ARE TO BE USED ONLY FOR:
MODEL PL855
MAINTENANCE INSTRUCTIONS
Cam bearing: Grease cams on the zerks provided every 10
hours of operation. We recommend Almagard® #3752 Grease
from Lubrication Engineers®, Inc. Check for wear periodically.
Shaft bearings: Grease both crank shaft ball bearings on the
zerks provided every 100 hours of operation.
Wheel bearings: Grease wheel ball bearings on the zerks
provided every 100 hours of operation.
Engine oil/filter: See engine manufacturer's instructions.
Change oil and filter at least once a season per engine
manual.
V-Belt: Adjust V-belt tightness with adjustment spool located
on engagement handles. Do not overtighten V-belt. This puts a
load on the engine gear box bearings. The belt is tight enough
when it does not slip during the operating cycle.
Tines (threaded type): These are adjustable by only the
thickness of the jam nut approximately 1/4" and the openings
should face the rear of the PLUGR. They are replaceable by
loosening the jam lock nut and unscrewing the tine. All threads
are right hand. Install the tine with the jam lock nut on the tine
and use maximum threads inserted into the tine casting.
Tighten jam lock nut against the tine casting.
Decals: All safety decals are available for replacement at no
cost. Do not operate without all warning labels clearly
readable
.
Machine Width
Aeration Width Per Pass
Hole Centers
Hole Depth (Up to)
Plug Diameter
Approx. Sq. Ft. Per Hour (Up to)
Shipping Weight
Actual Machine Weight
Tire
Belt Drive Clutch
Nylatron Cam Bearings
SPECIFICATIONS
2 3/5" x 7 1/2"
Double V-type
34"
30"
2 3/4"
5/8"
35,000
440 lbs.
360 lbs.
12"
Publicidad
Tabla de contenido
